Nortel Networks NN46205-310 Regulatory Information and Safety Precautions, FCC Statement USA only

Page 5

.

5

Regulatory Information and Safety Precautions

Read the information in this section to learn about regulatory conformities and compliances.

International Regulatory Statements of Conformity

This is to certify that the Nortel 8000 Series chassis and components installed within the chassis were evaluated to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards:

•EMC—Electromagnetic Emissions—CISPR 22, Class A

•EMC—Electromagnetic Immunity—CISPR 24

•Electrical Safety—IEC 60950, with CB member national deviations

Further, the equipment has been certified as compliant with the national standards as detailed in the following sections.

National Electromagnetic Compliance (EMC) Statements of Compliance

FCC Statement (USA only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 5

Contents Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity EN 55 024 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 300386 Statement EC Declaration of ConformityBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Nortel Command Line Interface FeaturesNew in this release Other changesConnecting the modem using the Nncli Connecting the modem using the CLISetting the system date and time using the CLI Setting the system date and time using the NncliNavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Safety precautions navigation Safety precautionsPersonal safety Check Accessory Use toCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsNumber Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the Nncli Setting system date and time using the CLIProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityMaster slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Fan tray safety warning message Translation of safety messagesRisques de blessure corporelle VerletzungsrisikoRischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Risques de blessure par choc électrique Preventing electrical shock warning statementVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosRisco de ferimento por choque elétrico Preventing hand injury warning statementRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurRiesgo de lesiones por las aspas del ventilador Safety danger statementRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreRisques de blessure oculaire par lumière laser Injury to eye warning statementRiesgo de lesión en los ojos por láser Risiko einer Augenverletzung durchLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start