Nortel Networks NN46205-310 quick start Vcci Statement Japan/Nippon only

Page 7

National Electromagnetic Compliance (EMC) Statements of Compliance 7

European Union and European Free Trade Association (EFTA) Notice

All products labeled with the CE marking comply with R&TTE Directive (1999/5/EEC) which includes the Electromagnetic Compliance (EMC) Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms (ENs). The equivalent international standards are listed in parenthesis.

•EN 55022 (CISPR 22)–Electromagnetic Interference

•EN 55024 (IEC 61000-4-2, -3, -4, -5, -6, -8, -11)–Electromagnetic Immunity

•EN 61000-3-2 (IEC 610000-3-2)–Power Line Harmonics

•EN 61000-3-3 (IEC 610000-3-3)–Power Line Flicker

VCCI Statement (Japan/Nippon only)

This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment.

If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

BSMI Statement for 8010, 8006 and 8003 Chassis (Taiwan only)

This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS 13438, Class A.

MIC Notice for 8010, 8006, 8003 Chassis (Republic of Korea only)

This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC). This device may not be sold for use in a non-business application.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 7

Contents Quick Start Legal Notice Contents Configuration International Regulatory Statements of Conformity Regulatory Information and Safety PrecautionsFCC Statement USA only EC Declaration of Conformity CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EN 300386 StatementBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of ComplianceNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Other changes FeaturesNortel Command Line Interface New in this releaseSetting the system date and time using the Nncli Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the CLINavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Check Accessory Use to Safety precautionsSafety precautions navigation Personal safetyCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Procedure job aid Grounding the 8010co chassis Installing a moduleLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a Pcmcia software card Installing a breaker interface panelStarting the system Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsDCE DB-25 Connecting a modem using the NncliNumber Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid clock set command output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid config setdate command sample outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityPrompt Action Procedure job aid Setup Utility prompt descriptionsMaster slot 5/6 Tftp Vlan Verletzungsrisiko Translation of safety messagesFan tray safety warning message Risques de blessure corporelleRisco de ferimento Preventing back injury warning statementRischio di lesioni personali Preventing back injury warning statement Riesgo de lesiones por choques eléctricos Preventing electrical shock warning statementRisques de blessure par choc électrique Verletzungsrisiko durchRisques de blessure provoquée par les pales du ventilateur Preventing hand injury warning statementRisco de ferimento por choque elétrico Rischio di lesioni per shock elettricoRischio di lesioni causate dalle lame del ventilatore Safety danger statementRiesgo de lesiones por las aspas del ventilador Risco de ferimento com lâmina do ventiladorRisques de blessure oculaire par lumière laser Injury to eye warning statementRischio di ustioni agli occhi dovute al laser Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Laser pode causar ferimentos no olhoRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start