Primera Technology 510212 manual For Users in the United States

Page 3

Digital Label Press 3 User’s Manual

For Users in the United States:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

„Re-orient or relocate the receiving antenna.

„Increase the separation between the equipment and receiver.

„Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

„Consult the dealer or an experienced radio/TV technician for help.

„Use of a shielded cable is required to comply with the Class A limits of Part 15 of the FCC Rules.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and/or obtain warranty service for this equipment.

For Users in Canada:

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

iv

Image 3
Contents Digital label and decal press Trademark Acknowledgements For Users in the United States Table of Contents Index HOW Your Press Works IntroductionDye-Sublimation Special FeaturesSafety Precautions Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Getting Started Choosing a Good LocationAbout Moisture Condensation Identifying the Parts Unpacking and InspectionControl Panel LCD Display Cancel Cutting Pressure Removing the Ribbon Cartridge and Blade Holder Installing the Blade Holder Installing the Media Input Assembly Installing the Media Output Assembly Applying Power Ribbon and Print Media IntroductionAbout Ribbons Loading Ribbon Into the Ribbon Cartridge Placing the Ribbon Cartridge Into the Printer About Print Media Loading the Print Media Roll Into the Press Open the Media Input Assembly Cover Cover Release Button Print Pressure Bracket Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual ??? Digital Label Press 3 User’s Manual Ribbons Digital Label Press 3 User’s Manual Running the Self Test Connecting the PressSelf Test Example Connecting the USB-TO-PARALLEL Interface Cable Select CD-ROM Drive and click Next Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Installing the Windows Printer Driver Installing and Setting Up the Printer Driver For WindowsDigital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Setting UP the Windows 98/ ME Printer Driver Paper Size Dither Mode Write Direct to Port Digital Label Press 3 User’s Manual Installing and Using the PressPrint Software for Windows Installing PressprintAbout Pressprint Using Pressprint Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Printing to Your Press Digital Label Press 3 User’s Manual Helpful Pressprint Hints Importing Vector vs. Bitmap Files Aligning Objects Anti-Aliasing Creating Serialized Labels Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Printing Multiple Spot Color Labels Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Maintenance Cleaning the Print HeadSupplies Required Cleaning the Inside of the Press Cleaning the Presss CaseCleaning the Platen Roller Clearing a Minor Print Media JAM Clearing a Ribbon JAMReplacing the Cutter Blade Clearing a Major Print Media JAMBlade Holder Cutter Arm Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Troubleshooting Printer Ribbon JAM Wrong Ribbon Ribbon Type Paper Core Rotation Error Ribbon Sensor Error Cutter Paper Loading Error Cutter Targets Center Biased to the right Print job rasterizes, but the press doesnt print Symptoms Cut line is not centered on the printed object Areas of my prints are scrambled or look like bar codes Digital Label Press 3 User’s Manual Printing Speed Technical SpecificationsEMC CENTRONICS-TYPE Parallel Interface Appendix aDigital Label Press 3 User’s Manual Index Print pressure bracket 26, 29 Printer cleaning kit 65, 66