Primera Technology 510212 manual Wrong Ribbon Ribbon Type

Page 80

Digital Label Press 3 User’s Manual

4.If the ribbon is torn, it can be fixed by cutting the torn edge and taping it to the take up roll. Be careful to line the ribbon up straight when repairing it as to avoid further jams.

5.Replace the ribbon and paper.

6.Close the lid of the unit and press both the Cancel and Retry buttons simultaneously. This will reset the unit. This is very important because the unit's memory buffer hold's much of the data for a print job. This will clear the buffer and allow the job to be resent.

7.Press Menu to bring up the PAGE LOAD SEQUENCE as described in the section on paper loading and press ENTER to run the paper load sequence.

8.Resend your job.

WRONG RIBBON: (RIBBON TYPE)

This message will be displayed when the ribbon installed in your press does not match the ribbon selected in the driver when the job was printed. The second line of the message will display the type of ribbon selected in the driver. Replace the ribbon as described in section 4-C, close the cover, and press the Retry button to continue printing.

OUT OF PAPER: (PAPER TYPE)

Media rolls are programmed to run exactly 100 prints to avoid the press accidentally printing when no media is present. Some extra material is on your roll to allow for waste that occurs during loading. This means that there may be some material left on the roll when this message is displayed, however, the press will not be able to print until a new roll of media is installed. The second line of the message will display the type of media needed to finish the current job (i.e. #200 ABR for #200 Series Dye-sublimation Adhesive Backed Receiver). Do the following to clear this error:

1.Cancel the print job from the Windows Spooler or Press Print.

2.Replace paper as described in section 4-D.

3.Close the lid of the unit and push both the Cancel and Retry buttons simultaneously. This will reset the press. This is very important because the unit's memory buffer holds quite a bit of data. This will clear the buffer.

4.Press Menu to bring up the PAGE LOAD SEQUENCE as described in the section on paper loading and press ENTER to run the paper load sequence.

5.Resend your job from Press Print.

Section 9: Troubleshooting

75

Image 80

Contents Digital label and decal press Trademark Acknowledgements For Users in the United States Table of Contents Index Introduction HOW Your Press WorksSpecial Features Dye-SublimationSafety Precautions Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual About Moisture Condensation Getting StartedChoosing a Good Location Unpacking and Inspection Identifying the PartsControl Panel LCD Display Cancel Cutting Pressure Removing the Ribbon Cartridge and Blade Holder Installing the Blade Holder Installing the Media Input Assembly Installing the Media Output Assembly Applying Power About Ribbons Ribbon and Print MediaIntroduction Loading Ribbon Into the Ribbon Cartridge Placing the Ribbon Cartridge Into the Printer About Print Media Loading the Print Media Roll Into the Press Open the Media Input Assembly Cover Cover Release Button Print Pressure Bracket Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual ??? Digital Label Press 3 User’s Manual Ribbons Digital Label Press 3 User’s Manual Connecting the Press Running the Self TestSelf Test Example Connecting the USB-TO-PARALLEL Interface Cable Select CD-ROM Drive and click Next Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Installing and Setting Up the Printer Driver For Windows Installing the Windows Printer DriverDigital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Setting UP the Windows 98/ ME Printer Driver Paper Size Dither Mode Write Direct to Port Digital Label Press 3 User’s Manual About Pressprint Installing and Using the PressPrint Software for WindowsInstalling Pressprint Using Pressprint Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Printing to Your Press Digital Label Press 3 User’s Manual Helpful Pressprint Hints Importing Vector vs. Bitmap Files Aligning Objects Anti-Aliasing Creating Serialized Labels Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Printing Multiple Spot Color Labels Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Supplies Required MaintenanceCleaning the Print Head Cleaning the Presss Case Cleaning the Inside of the PressCleaning the Platen Roller Clearing a Ribbon JAM Clearing a Minor Print Media JAMClearing a Major Print Media JAM Replacing the Cutter BladeBlade Holder Cutter Arm Digital Label Press 3 User’s Manual Digital Label Press 3 User’s Manual Troubleshooting Printer Ribbon JAM Wrong Ribbon Ribbon Type Paper Core Rotation Error Ribbon Sensor Error Cutter Paper Loading Error Cutter Targets Center Biased to the right Print job rasterizes, but the press doesnt print Symptoms Cut line is not centered on the printed object Areas of my prints are scrambled or look like bar codes Digital Label Press 3 User’s Manual Technical Specifications Printing SpeedEMC Appendix a CENTRONICS-TYPE Parallel InterfaceDigital Label Press 3 User’s Manual Index Print pressure bracket 26, 29 Printer cleaning kit 65, 66