Nortel Networks NN44200-300 manual Conventions for warnings

Page 25

Installation overview 25

Step

Description

Check

Note: If you are connecting the optional Nortel server subnet, do not power up unless your antivirus programs and Nortel security updates are installed first.

•

Connect the 1002rp server to the CLAN hub or switch (optional) (see "Connecting the server to the Nortel server subnet (optional)" (page 51)).

ATTENTION

To comply with EMC radiation requirements, a Class A hub must be located 10 m (33 ft.) away from the 1002rp server. Shielded Ethernet cables must be used.

•

Install the software feature dongle (see "Installing the Nortel software feature dongle" (page 52)).

•

Connect the power cords for all devices, and then power them up.

11 Start the 1002rp server (see "Connecting the server to power" (page 53)).

Conventions for warnings

You may encounter the following types of warnings in this guide. Do not ignore them.

DANGER

Warns you of an immediate electrical hazard which, if not avoided, can result in shock, serious injury, or death.

WARNING

Warns you of a situation in which you can be injured if instructions are not followed exactly as stated.

Nortel CallPilot

1002rp Server Hardware Installation

NN44200-300 01.01 Standard

5.0 23 February 2007

Copyright © 2007, Nortel Networks

Nortel Networks Conﬁdential

Image 25

Contents 1002rp Server Hardware Installation Trademarks Japan Denan statement Information for JapanJapan Vcci statement Page February Publication HistoryPublication History Contents Contents Getting help from the Nortel Web site Getting help over the phone from a Nortel Solutions CenterGetting help through a Nortel distributor or reseller Server dimensions and weight Server featuresThis chapter IntroductionEnvironmental speciﬁcations Front panel features front view without the front bezelRear panel diagram Alarm boardOverhead view of empty server showing PCI and ISA connectors Reference Documents Slot assignments1002rp server description T1/SMDI Slot deﬁnition and slot numberingBRD20 Network connectivitySample network setup Communication Server Sample network setup MeridianCallPilot Elan subnet and Nortel server subnet setup Switch connectivityMeridian 1 or Communication Server 1000 systems Network requirementsSupported peripheral devices Remote access connectivityDeviceDescription Installation checklist Installation overviewPreparing for installation Conventions for warnings To unpack the equipment Unpacking the 1002rp serverRemoving the front bezel and server cover What is next?To remove the front bezel Remove the front bezel see To remove the front bezel To remove the server coverTo inspect the server interior Inspecting the server interiorInstallation and Configuration To replace the front bezel after installation is completeEnd Preparing for installation Safety information Safety precautionsEquipment handling guidelines About the power supply module Installing the second power supply module AC or DCAC versus DC systems To install the power supply module AWG DC wire gauge tablesDC rack cabling Metric wire conversionPower supply installation Rack power and grounding DC power distribution rationale About the power distribution unitPDU power and grounding Multiple PDUsDC power input PDU terminal blocks and wiring diagramTo bring DC power and ground into the PDU Bringing power and ground into the PDUTo install the server Installing the serverPreparing the modem Modem DIP switchesRequired equipment DIP To set the modem DIP switchesContinue with Connecting peripherals to the server Connecting peripherals to the server To connect the modem to the server Media Access Control address Connecting the server to the Elan subnetTo connect the server to the Elan subnet Server will To connect the server to the Nortel server subnet Connecting the server to the Nortel server subnet optionalTo install the software feature dongle Installing the Nortel software feature dongleRequirements Before you begin Connecting the server to powerPlug the server AC power cord into the server rear panel To connect the 1002rp AC server to powerTo connect the 1002rp DC server to power To start the server Copyright 2007, Nortel Networks Ferrites secured to an external cable Index Index Tlan Index Page 1002rp Server Hardware Installation