Transcend Information TS8GSSD25S-S dimensions Standby E2h, Standby Immediate E0h, Write Buffer E8h

Page 36

TS8GSSD25S-S

 

TS16GSSD25S-S/M

 

TS32GSSD25S-S/M

 

TS64GSSD25S-S/M

 

TS128GSSD25S-M

2.5” Solid State Disk

TS192GSSD25S-M

STANDBY (E2h)

This command causes the device to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately.

STANDBY IMMEDIATE (E0h)

This command causes the drive to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately.

WRITE BUFFER (E8h)

This command enables the host to write the contents of one 512-byte block of data to the device’s buffer.

WRITE DMA (CAh)

Write data to sectors during Ultra DMA and Multiword DMA transfer. Use the SET FEATURES command to specify the mode value.

WRITE DMA EXT (35h)

48-bit feature set mandatory command. Write data to sectors during Ultra DMA and Multiword DMA transfer. Use the SET FEATURES command to specify the mode value.

WRITE DMA FUA EXT (3Dh)

48-bit feature set mandatory command. This command provides the same function as the WRITE DMA EXT command except that regardless of whether volatile and/or non-volatile write caching in the device is enabled or not, the user data shall be written to non-volatile media before command completion is reported.

WRITE FPDMA QUEUED (61h)

NCQ feature set mandatory 48-bit command. This command causes data to be transferred from the host to the device.

WRITE MULTIPLE (C5h)

This command is similar to the Write Sectors command. Interrupts are not presented on each sector, but on the transfer of a block which contains the number of sectors defined by Set Multiple command.

Transcend Information Inc.

36

V1.08

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Placement Features DimensionsDescription V1.08Specifications Model P/N Sequential ReadMax Sequential WriteMaxModel P/N User Max. LBA Cylinder Head Sector Data Reliability Data Retention Operating Non-OperatingCompliance Package Dimensions Pin Assignments Pin LayoutPin No Pin Name Block Diagram Reliability Wear-Leveling algorithmECC algorithm Bad-block managementOut of bank signaling Sata InterfaceComreset TS192GSSD25S-M Cominit TS192GSSD25S-M Power on sequence timing diagram Power on sequenceATA command register Command Table Command Name CodeSET Features ATA Command Specifications Identify Device Information Default Value Word Value DescriptionPIO data transfer cycle timing mode Reserved TS192GSSD25S-M Minor version number TS192GSSD25S-M TS192GSSD25S-M Current AAM value 15-8 Vendor’s recommended AAM value 95-99 Idle E3h Idle Immediate E1hInitialize Device Parameters 91h Read Buffer E4hLog Address Log Name Feature Set Access Read DMA EXT 25hRead Fpdma Queued 60h Read LOG EXT 2FhSecurity Disable Password F6h Read Verify Sectors 40h/41hRead Verify Sectors EXT 42h Recalibrate 10hSecurity set Password data content Security SET Password F1hSecurity Unlock F2h Features register Value and settable operating mode Code Smart Subcommand Smart Function Set B0hByte 2-361 Individual attribute data Byte DescriptionAttribute ID information is listed in the following table Description Detail Information ByteSmart Read Attribute Threshold Smart Enabl Operations Standby E2h Standby Immediate E0hWrite Buffer E8h Write DMA CAhWrite Multiple EXT 39h Write Multiple FUA EXT CEhWrite Sectors 30h/31h Write Sectors EXT 34hOrdering Information Taiwan Germany
Top Page Image Contents