Transcend Information TS32GSSD25S-S, TS128GSSD25S-M, TS64GSSD25S-M dimensions Smart Enabl Operations

Page 35

TS8GSSD25S-S

 

TS16GSSD25S-S/M

 

TS32GSSD25S-S/M

 

TS64GSSD25S-S/M

 

TS128GSSD25S-M

2.5” Solid State Disk

TS192GSSD25S-M

SMART ENABL OPERATIONS

Enables the SMART function. This setting is maintained when the power is turned off and then back on. Once the SMART function is enabled, subsequent SMART ENABLE OPERATIONS commands do not affect any parameters.

SMART DISABLE OPERATIONS

Disables the SMART function. Upon receiving the command, the drive disables all SMART operations. This setting is maintained when the power is turned off and then back on.

Once this command has been received, all SMART commands other than SMART ENABLE OPERATIONS are aborted with the Aborted Command error.

This command disables all SMART capabilities including any and all timer and event count functions related exclusively to this feature. After command acceptance, this controller will disable all SMART operations. SMART data in no longer be monitored or saved. The state of SMART is preserved across power cycles.

SMART RETURN STATUS

Reports the drive reliability status.

Values reported when a predicted defect has not been detected:

Cylinder Low register: 4Fh

Cylinder High register: C2h

Values reported when a predicted defect has been detected:

Cylinder Low register: F4h

Cylinder High register: 2Ch

SMART ENABLE/DISABLE AUTOMATIC OFF-LINE

Enables (when Sector Count register = “F8h”) or disables (Sector Count register = “00h”) the automatic off-line data collection function. The automatic collection is disabled if a value of “00h” is set in the Sector Count register before a subcommand is issued. If automatic collection is disabled, the drive can still save attribute information during normal operation, such as during the power-on/off sequence or error correction sequence. The automatic collection function is enabled if a value of “F8h” is set in the Sector Count register before the command is issued. Values other than “00h” and “F8h” are vendor-specific.

Transcend Information Inc.

35

V1.08

Page 34 Page 36
Image 35
Page 34 Page 36
Contents V1.08 Placement FeaturesDimensions DescriptionSpecifications Model P/N User Max. LBA Cylinder Head Sector Model P/N Sequential ReadMaxSequential WriteMax Compliance Data Reliability Data RetentionOperating Non-Operating Package Dimensions Pin No Pin Name Pin AssignmentsPin Layout Block Diagram Bad-block management ReliabilityWear-Leveling algorithm ECC algorithmSata Interface Out of bank signalingComreset TS192GSSD25S-M Cominit TS192GSSD25S-M Power on sequence Power on sequence timing diagramATA command register Command Name Code Command TableSET Features ATA Command Specifications Word Value Description Identify Device Information Default ValuePIO data transfer cycle timing mode Reserved TS192GSSD25S-M Minor version number TS192GSSD25S-M TS192GSSD25S-M Current AAM value 15-8 Vendor’s recommended AAM value 95-99 Read Buffer E4h Idle E3hIdle Immediate E1h Initialize Device Parameters 91hRead LOG EXT 2Fh Log Address Log Name Feature Set AccessRead DMA EXT 25h Read Fpdma Queued 60hRecalibrate 10h Security Disable Password F6hRead Verify Sectors 40h/41h Read Verify Sectors EXT 42hSecurity Unlock F2h Security set Password data contentSecurity SET Password F1h Features register Value and settable operating mode Smart Function Set B0h Code Smart SubcommandByte Description Byte 2-361 Individual attribute dataDescription Detail Information Byte Attribute ID information is listed in the following tableSmart Read Attribute Threshold Smart Enabl Operations Write DMA CAh Standby E2hStandby Immediate E0h Write Buffer E8hWrite Sectors EXT 34h Write Multiple EXT 39hWrite Multiple FUA EXT CEh Write Sectors 30h/31hTaiwan Germany Ordering Information
Top Page Image Contents