American Power Conversion AP9207 manual Specifications, On next

Page 60

Specifications

Basic port pin The following limitations and capabilities apply to the Basic

assignments ports of Share-UPS:

•Pins 3, 5, and 6 are open collector outputs which must be pulled up to a common referenced supply no greater than +40 Vdc. The transistors are capable of a maximum non-inductive load of 25 mAdc. Use only Pin 4 as the common.

•The output at Pin 2 generates a low-to- high RS-232level when the device is signaling an On Battery con- dition. The pin is normally at a low RS-232 level.

•Share-UPS may be signaled to shut down the UPS by applying a high RS-232 level to Pin 1 for 4.5 sec- onds. Shutdown is also dependent on the UPS status and the Share-UPS shutdown mode (see “Configur- ing Share-UPS,” on page 23).

Continued on next page

54

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Share-UPS Thank You Contents Setting Up Share-UPS Using the Share-UPS Menus Product Information Introduction Following list shows some of the features of Share Supports advanced or simple signaling on itsCan delay shutdown of the UPS until all servers have UPS and Share-UPS. See Using the Share-UPSOn next Cable supplied with your APC UPS Product Description Tery and Low Battery conditions in the UPS. For further Information see Simple versus smart signaling TableOn page 10. For Basic port specifications, see Basic port Pin assignments, onProduct Description If the LED Is… Then Share-UPS… Labeled… Product Description Simple Signaling Smart Signaling Key ConceptsCommunication Types Key Concepts If the UPS had previously been connected using Smart signalingLow Battery condition at the UPS. Share-UPS generates a To the configured shutdown mode see Configuring ShareUPS on page 23, when it may force a Low Battery signal An On Battery signal, causing the servers to shut downKey Concepts Installing Multiple Accessories Accessory slot with the higher number Accessory Priority PositionInterface Expander AP9604. For installation instructions, refer to the user If you need additional SmartSlot capacity betweenShare-UPS unit and the master server, you can purchase an APC Expansion Chassis AP9600 or Triple ChassisInstalling Share-UPS Mounting Share-UPS NetShelter Figure Mounting Share-UPS on a wall Figure Connecting Share-UPS Configuring Share-UPS, onIf using Optional Power input see Optional If daisy-chaining multiple Share-UPS unitsAte cable. See Choosing simple signaling If an accessory, such as Measure-UPS II orAn Expansion Chassis, is already using Share-UPS use simple signaling for moniConfiguring Share-UPS Behavior Confirmed shutdown mode Effect Down delay for a time longer than Share-UPS timer Setting. Otherwise, if the power returns afterShutdown delay, go to ConfigurationEvent Actions and select UPS On Battery from the EventIf you want to change Share-UPS settings Com If configuring multiple Share-UPS units repeatTroubleshooting on Steps in the order given. If Share-UPS fails this test, seeUsing the Share-UPS Menus Using the Management PortUsing a dumb terminal or a computer and terminal emula Tion software, you can access the UPS remotely.Password-protected menu interface allows you to view Load, battery conditions, and current UPS statusNected, after three unsuccessful password For security, change the password as soonAs possible. See Share-UPS Settings Characters long, and is case-sensitiveMain Menu Main menu The following figure shows the Main menu. FigureMeasure-UPS environmental monitoring accessory UPS accessoryMain menu only if Share-UPS has detected an APC For a description of the Measure-UPS Status screenFollowing table describes the items that appear on Main menuDescription Behavior Connected UPS, output and load readings, battery informa Access the UPS Status display, type s from the Main menuUPS Status Display Following figure shows the UPS Status displayUPS Status Display Definitions Waiting to Power Load Tions on demand through Share-UPS. To access the UPS UPS Control MenuStatus display, type c from the Main menu Following figure shows the UPS Control menuUPS Control menu It is connected to the UPSShare-UPS Settings Menu Share-UPS Settings menu allows you to configureFollowing figure shows the Share-UPS Settings menu Menu, type d from the Main menuShare-UPS Settings menu Definitions Paging Setup Menu Site IDspaceevent codeDuring a utility power outage when Share-UPS is config Following figure shows a typical sequence of eventsUred for paging Following figure shows the Paging Setup menu Following table lists some common modem commandsThat you may include in your dial string see Share-UPS Information, see the documentation supplied withPaging Setup menu Setting DescriptionPaging Setup Menu Definitions Warranty Information Claims by third parties, or otherwise. This warranty gives Purpose. Some jurisdictions do not permit limitation orExclusion of implied warranties therefore, the aforesaid Specifically, APC is not liable for any costs, such as lostTroubleshooting Trouble Shooting Trouble Shooting Table For problems not covered in the troubleshooting chart see Troubleshooting on page 26, or if the problemPersists, follow this procedure Material authorization RMA numberLife-Support Policy Specifications Assignments Specifications Normally Open Communications port. The port is configured as data termi Management port is a standard 9-pin RS-232 serialData bits with 1 start bit, 1 stop bit, and no parity Management port pin assignments are listed in the folFollowing table shows the product specifications for SpecificationShare-UPS Product Specifications Symbols IndexIndex Re-Boot All Servers Y, Z Page W. a p c c . c o m
Top Page Image Contents