American Dynamics ADMPCPU Associating Monitors to Cameras, Adding Satellite Sites to Keyboards

Page 61

Adding Satellite Sites to Keyboards

1.Click Add on the right side of the Site Access screen. The Add Sites dialog box appears.

Figure 130. Add Sites dialog

The Add Sites dialog box provides three options. To select an option:

2.Click the button beside it and complete the required information. The options are:

Replace with the following sequence – Enter a range of sites; for example: 1-30.

Add a single Site – Click the up or down arrows to select a site.

Add a range of Sites – Click the up or down arrows on the “from” and “to” fields to select a range of sites.

3.Click OK to save your site choices or Cancel to close the dialog box without saving your choices.

Removing Satellite Sites from Keyboards

1.Click on a keyboard (any cell in the keyboard row) in the upper screen.

2.Click on the satellite sites listed on the Site Access screen (lower screen).

3.Click the Remove button on the right side of the site access screen. This removes the satellite sites associated with that keyboard.

Associating Monitors to Cameras

The Partitions – Monitors to Cameras screen determines which cameras can be called to which monitors. This method of association simplifies partitioning a range of cameras to specific monitors.

If you want to partition multiple cameras so they cannot be accessed by specific monitors, you must configure in the Partitions – Cameras to Monitors screen, the access on a per camera basis rather than on a per monitor basis (as in the Partitions – Monitors to Cameras screen).

Click on the Partitions – Monitors to Cameras link in the Explore menu to begin. The following screen appears (Figure 131 on page 59).

Figure 131. Partitions – monitors to cameras screen

The Partitions – Monitors to Cameras screen is split into two sections:

The upper screen shows existing monitor definitions and allows you to create new definitions.

The lower screen allows you to set up contact arming and view event timers for each monitor.

Note: Changes made in this screen are also reflected in the Partitions – Cameras to Monitors screen (Figure 110 on page 51).

You can create and edit monitor definitions.

MEGAPOWER CPU ADMINISTRATOR’S GUIDE

8200-0421-03, REV. G

59 of 82

Image 61
Contents MegaPower CPU Page About the Product MegaPower CPUAbout this Guide Contents Removing Monitors or Satellite Sites Access From Keyboards MegaPower CPU Front Panel MegaPower 3200 Video-Matrix Cctv System Dual CPUCPU Rear Panel MegaPower System OverviewSystem Components System CapabilitiesCompatible System Keyboards System FeaturesOperator Tasks Administrator TasksUnderstanding the Screen Icons Initializing the SystemDirect Connection RS-232 Port S3 SoftwareEthernet Port Easy CPU Software Ethernet Network ConnectionADCC1100 Using an IP Address Assigned by the Network Dhcp ServerStandalone Mpcpu Enter ADCC0200/0300System Menu screen Using a Static IP AddressRead Cycle Firewall SetupError Message Example Installing Easy CPUBeginning the Installation Write CycleLanguage, go to Appendix a End User License Agreement on Choose Setup Language dialogLicense Agreement screen Starting Easy CPU Configuring PreferencesSaving Data on the Hard Drive Viewing Configuration File PropertiesFactory-Default or Existing Configuration Data in CPU Retrieving Configuration DataConfiguration Data File Only in PC Write to Mpcpu and/or Save Configuration To File dialog New Configuration File Login Manager dialog Adding a User LoginLogin dialog Logging in Users for CPU Read/Write AccessEasy CPU Main Screen Overview Programming the MegaPower CPUDropdown Menus File Edit HelpChecking the System Status Settings Window Display AreaMonitor Status Explore MenuCamera Status Passive Hot Switch StatusError Log Status Setting System Options Configuring the System− Installing a Tftp server Setting the Date and Time Using the Dialog Box Setting System Date and TimeSystem Date & Time dialog Setting the Date and Time Using the KeyboardConfiguring the Dome/PTZ Device Direct Connection Setting Port ConfigurationsDome/PTZ Device Direct Connect Configuration screen Creating Salvos Configuring SwitchingSalvos Preset or Pattern Dropdown List Creating Tours Deleting Salvos or Alarm ContactsTours Section Event Timers Alarm Tables Event TimersScheduling System Tours with the Event Timer Event Timer ToursDeleting Tours in the Event Timer Screen Alarm TablesSetting Up Alarm Monitors Configuring AlarmsAdding Monitor Definitions Group these monitors together Viewing Event Timers Event TimersDeleting Event Timers Contact ArmingDropdown List Creating Alarm Monitor/ Contact TablesEmail Message dialog Defining System Devices Alarm MessagesEmail Messages Defining CamerasAdding and Deleting Calling Contacts to Cameras on Adding Camera DefinitionsEditing Camera Definitions Adding and Deleting Calling Contacts to CamerasDeleting Calling Contacts Associating Salvo Callups to CamerasDeleting Salvo Callups Defining Keyboards Adding Monitor Access to KeyboardsAdding Keyboard Definitions Editing and Deleting Keyboard DefinitionsAdding a Range of Monitors Adding Site Access to KeyboardsRemoving Monitor or Site Access Configuring Keyboard/User Keyboards and PrioritiesUser Enable Logon checkbox settings Deleting Keyboard/User Priorities Settings Configuring the Keyboard/User Priority SettingsDefining Satellite Sites Controlling Access with PartitionsAssociating Cameras to Monitors Deleting Satellite SitesPartitions cameras to monitors screen Changing Calling Contacts Editing Camera DefinitionsRemoving Calling Contacts Associating Keyboards to CamerasDeleting Keyboard Definitions Editing Keyboard DefinitionsAdding Cameras to Keyboards Adding a Range of CamerasAssociating Keyboards to Monitors Removing Monitors or Satellite Sites Access from KeyboardsAdding Monitors to Keyboards Adding Monitor Access to KeyboardsRemoving Monitors from Keyboards Associating Keyboards to SatellitesAdding Site Access to Keyboards Adding Satellite Sites to Keyboards Associating Monitors to CamerasRemoving Satellite Sites from Keyboards Adding Monitor Definitions Adding Contacts Adding a Range of CamerasPerforming a Ping Test Regulatory Compliance DeclarationsRegulatory Type Other DeclarationsScope of License Appendix a End User License AgreementExport Restrictions Appendix B MegaPower CPU System Defaults Appendix C MegaPower CPU Front Panel LCD Menu Structure Purpose Protocol Port Description Appendix D Port Number AssignmentsF1 Special Function Keys Appendix E Auxiliary Key Code FunctionsF2 Special Function Keys 60-F2 55-F261-F2 62-F2Video Loss Detection dropdown menu Appendix F Configuring Video Loss DetectionMegapower CPU ADMINISTRATOR’S Guide Alarm Receipt Appendix G Alarm Programming OverviewAlarm Arming and Response Alarm Display IndicatorsAlarm Queuing Method Alarm Display MethodAlarm Clearance Method Appendix H Monitor Arming MethodsMegapower CPU ADMINISTRATOR’S Guide Single Display, Sequence Queuing Appendix I Monitor Arming CodesSingle Display, Hold Queuing Block Display, Sequence QueuingDual Display, Hold and Sequence Queuing Block Display, Hold QueuingAppendix J Alarm Arming Notes Setting Up Satellite Sites Appendix K Satellite Configuration OverviewSatellite Site Connections Site 1 Source Site Site 1 Source and Receiving Site 2 Source and Receiving Page 8200-0421-03 G