AC International SV01B, V0100 Icon Signal Words, Operation, Warns of impending danger, Equipment

Page 5

Safety information

All safety information given in these Operating Instructions have the same layout:

Signal Word! (characterizes the severity of the danger)

Note (describes the danger and informs on how to proceed)

 

Icon

Signal Words

 

 

 

 

 

 

 

 

 

Warning of

DANGER!

Warns of impending danger.

 

 

 

hazardous electrical

 

Consequences if disregarded:

 

 

 

voltage

 

 

 

 

 

Death or severe injuries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning of a

WARNING!

Warns of potential, very hazardous situations.

 

 

 

general danger

 

Consequences if disregarded:

 

 

 

 

 

 

 

 

 

 

Death or severe injuries.

 

 

 

 

 

 

 

 

 

Warning of damage

STOP!

Warns of potential damage to material and

 

 

 

to equipment

 

equipment.

 

 

 

 

 

Consequences if disregarded:

 

 

 

 

 

Damage to the controller/drive or its

 

 

 

 

 

environment.

 

 

 

 

 

 

 

 

 

Information

Note

Designates a general, useful note.

 

 

 

 

 

 

 

 

If you observe it, handling the controller/drive

 

 

 

 

 

system is made easier.

 

 

 

 

 

 

 

 

 

 

 

 

Note for UL approved system with integrated controllers: UL warnings are notes which apply to UL systems. The documentation contains special information about UL.

 

• Suitable for use on a circuit capable of delivering not more than 200,000 rms

 

symmetrical amperes, at the maximum voltage rating marked on the drive.

 

• Use minimum 75 °C copper wire only.

Warnings!

• Shall be installed in a pollution degree 2 macro-environment.

 

Operation

Systems including controllers must be equipped with additional monitoring and protection devices according to the corresponding standards (e.g. technical equipment, regulations for prevention of accidents, etc.). The controller may be adapted to your application as described in this documentation.

DANGER!

•After the controller has been disconnected from the supply voltage, live components and power connection must not be touched immediately, since capacitors could be charged. Please observe the corresponding notes on the controller.

•Please close all protective covers and doors prior to and during operation.

•Do not cycle input power to the controller more than once every two minutes.

ENGLISH

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operating Instructions Contents Claim About these instructionsVisible transport damage immediately to the forwarder Visible deficiencies / incompleteness immediately to yourInstallation Safety informationGeneral Electrical connectionOperation Icon Signal WordsWarns of impending danger Warns of potential damage to materialStandards and application conditions Technical data240VAC Models Ratings120VAC Doubler / 240VAC Models Drive Derating Mains Output CurrentType InstallationDimensions and mounting Power Connections Electrical installationMains connection to 120VAC Single-Phase Supply Mains connection to 240VAC Single-Phase SupplyMotor Connection Mains connection to Three-Phase SupplyMains and Motor Terminations ESV…N06T… 3/PE ACRecommendations Type Fuses/cable cross-sections240V 400VAssertion level of digital inputs Control terminals13A Local Keypad & Display Local Mode P100 = 0, 4, this button will start the driveCommissioning Electronic programming module EPM Parameter settingDrive Displays and Modes of Operation Parameter menu Basic Setup ParametersCode Possible Settings No. Name Default Selection Default setting is Motor Overload Selection Drives except when using resetMinimum P103 AccelerationPrior to faulting or power loss Faults, or when power is appliedPower-up Upon a stop command, allowing2 I/O Setup Parameters Code Possible Settings Name Default Selection Attempts fail De-energizes when PID feedbackActive for start control Network Control Active Standard Reference ActiveTB-14 Output VDC Load VDC Torque VDC Power kWDynamic Braking Network Activated Requires optional communicationCode Advanced Setup ParametersDisplay Depends on mode of operation See Section CLim When the limit is reached,Slip 10.0 Drive displays , and eitherFault circuitry may be disabled! Check P100 and P121...P123 Reset to 60 Hz default settings See NoteDisplayed when P199 is set to 1 or Is installedPID Parameters P242 or when the PID loop Sleep DelayP200 = 0…2 Drive will start again Setpoint by more than the valueVector Parameters Motor Stator 4.00 Calibration Enabled Must be programmed first An alternatingCurrent Loop 9990 If P300 = 2...5, motor calibrationNetwork Parameters Diagnostic ParametersKeypad Status Display Terminal and Protection Status DisplayStatus / Warning Cause Remedy Troubleshooting and DiagnosticsStatus/Warning Messages Example Drive Configuration MessagesStop Source Display Format =Fault Cause Remedy Fault MessagesMOP function Up, Down Digital Input More than one digital input set forChange PID setpoint reference Is set to 13 orVerify drive and motor are proper Page SV01B

V0100, SV01B specifications

The AC International SV01B and V0100 represent a significant advancement in the realm of audio technology, specifically tailored for audiophiles and professionals seeking high-fidelity sound reproduction. These models have garnered attention for their impeccable engineering and innovative features designed to enhance the listening experience.

One of the standout characteristics of the SV01B is its superior sound quality, achieved through high-resolution audio capabilities. This model supports various audio formats, ensuring that users can enjoy music in its purest form. The SV01B employs advanced digital signal processing (DSP) that optimizes audio performance, reducing distortion and maintaining clarity at high volumes. Coupled with a robust amplifier, the SV01B delivers deep bass and crystal-clear highs, making it suitable for listening to a range of genres from classical to modern electronic music.

The V0100, on the other hand, brings together cutting-edge wireless technology with exceptional sound. It incorporates Bluetooth 5.0, ensuring a stable and high-quality connection with compatible devices. This feature allows users to experience seamless streaming without the hassle of tangled wires. The V0100 also supports aptX and AAC codecs, enabling low-latency audio playback, which is particularly beneficial for video content and gaming. Additionally, its multi-device connection capability allows users to switch between devices effortlessly, enhancing convenience.

Both the SV01B and V0100 showcase elegant designs that blend practicality with aesthetics. The chassis of these models is crafted from high-grade materials, providing durability while minimizing resonance. Furthermore, they feature intuitive controls, making it easy to adjust settings or switch tracks without interrupting the listening flow.

Battery life is another significant advantage of the V0100, which offers an impressive runtime on a single charge, ensuring that users can enjoy extended listening sessions without frequent recharging. The LED indicators provide clear feedback on connectivity and battery status, enhancing user experience.

In conclusion, the AC International SV01B and V0100 are remarkable audio devices that combine outstanding sound quality, advanced technology, and user-friendly features. They cater to both casual listeners and dedicated audiophiles, making them an excellent choice for anyone looking to elevate their audio experience.
Top Page Image Contents