Panamax MX5102 manual Front and Back Panel Descriptions

Page 5

Front and Back Panel Descriptions

Power Switch Press the power button to turn the unit ON or OFF.

Unsafe Voltage

Meter Dimmer /UPS Test Button

Indicator

A quick press of the button will cycle the

This LED will illumi-

meter and front panel through several

nate in red to warn

levels of brightness. Press and hold the

the user that an

button to initiate an UPS test cycle. During

unsafe voltage level

UPS mode, pressing the button will turn off

is occuring.

the internal warning buzzer.

Digital Voltmeter/UPS Status Display

During normal operation, the digital LED voltmeter indicates the incoming line voltage. If line voltage drops below 90VAC, or exceeds 132VAC, the Unsafe Voltage LED will flash, and during battery backup (UPS) mode the display will indicate the estimated minutes of battery backup time.

Removable Battery Access Panel Easy to remove for battery access and replacement.

 

UNSAFE

WIRING

BANKS

VOLTAGE

FAULT

 

 

 

O VOLTS IN

 

 

 

EST’D BATTERY: 60 MIN

1

2

3

4

POWER

 

 

DISPLAY/

 

 

 

UPS TEST

MX5102

Outlet Bank 1

Outlet Bank 2

Outlet Bank 3

Outlet Bank 4

Wiring Fault Indicator

Indicator

Indicator

Indicator

Indicator

This LED will illuminate in red to warn the user that a wiring problem such

Illuminated blue

Illuminated blue

Illuminated blue

Illuminated blue

as a bad/missing ground or reversed wiring exists within the AC receptacle.

when outlet bank 1

when outlet bank 2

when outlet bank 3

when outlet bank 4

If illuminated, disconnect all equipment and contact an electrician to insure

is always on.

is switched on.

is switched on.

is on.

outlet is properly wired.

Outlet Bank 4

Two always on, battery pow- ered, surge protected outlets for connected equipment ensure temporary uninterrupted operation of connected equip- ment during a power failure.

Outlet Bank 3

Two switched, high-current outlets controlled by the front panel Power Button or the DC Trigger input. Bank 3 has a 5 second turn on delay and turns off immediately. The High Current outlet provides power from a low impedance noise filtration circuit that does not limit the current to your equipment. Its output is noise isolated from all other outlet banks.

Circuit Breakers for

IR Control Section

Overload Protection

Indicator LED’s – Indicates

Resettable circuit

status IR Output Jacks –

breakers provide optimal

Standard 1/8” (3.5mm)

overload protection.

mono jack for connection to

 

an IR flasher (IR flashers not

 

included)

Universal TV Coaxial Jacks 3 pairs of bidirectional protec- tion circuits optimized for satellite, cable, and antenna TV signal lines.

 

 

 

 

 

 

 

 

 

 

CIRCUIT

 

 

 

 

 

 

 

 

 

 

BREAKER

 

 

 

 

 

 

 

 

 

 

UPS

 

 

 

 

 

 

 

 

 

 

CIRCUIT

 

 

 

 

 

 

 

 

 

 

BREAKER

BANK 4

BATTERY

BANK 3

HIGH

BANK 2

SWITCHED

BANK 2

SWITCHED

BANK 1

ALWAYS

MAIN

BACKUP

CURRENT

ON

 

 

 

 

 

 

 

 

 

IR OUT __ STATUS _ IR LEARN _____________ IR INPUT _

UNIVERSAL COAX PROTECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

2

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LAN IN

LAN OUT

TEL IN TEL OUT

MAIN POWER

IN

120VAC/12A

 

12V

TRIGGER

Outlet Bank 2

Four switched outlets with Linear Filtration Technology (LiFT) controlled by the front panel Power Button or the DC Trigger input. Bank 2 will turn on immediately and turn off after 5 seconds. Its output is noise isolated from all other banks.

Outlet Bank 1

Two always on outlets with Linear Filtration Technology (LiFT). Power will only be turned off under a fault con- dition, or when the Power Button is switched off. Its output is noise isolated from all other outlet banks.

AC Power Cord

Voltage Sense Trigger Output

3.5mm (1/8”) Mini-Plug jack.

LAN Jack

Protection circuit for one 10/100 baseT Ethernet line. Incoming LAN line MUST be plugged into the LINE jack. Patch cord to the equipment MUST be plugged into the EQUIP jacks. 8 wire protection, 50V clamping.

Phone Jack

Protection circuit for one standard telephone or pay-per-view lines. Phone circuit is auto-resetting. Incom- ing phone cord MUST be plugged into the LINE jack. Patch cords to the equipment (satellite receiver, digital video recorder, telephone, etc.) MUST be plugged into the EQUIP jacks.

2-wire protection, 270V clamping.

4

Image 5
Contents MX5102 Instructions FeaturesBefore you begin unpacking inspect the MX5102 upon receipt Table of ContentsFCC Notice Important Safety InstructionsFCC Notice Sequential Start/Shutdown Key Features and FunctionsFront and Back Panel Descriptions MX5102 Operation Installing Your MX5102MX5102 Advanced Operation Panamax Power Conditioner Limited Product Warranty Warranty InformationUpgrade Policy Year Battery WarrantyCaractéristiques Avant de commencer Table des matièresMX5102 Spécifications Alimentation c. aAvis FCC Pour votre sécuritéAvis FCC Principales caractéristiques et fonctions Prises coaxiales universelles pour TV Contrôle infrarougeMX5102 Opération Installation MX5102IR Panne de l’opération Patent Pending Learning IR ControlIR LED Color & Status Pour programmer IR sortiePrograma de actualización de productos Renseignements sur la garantieGarantie de 2 ans de batterie MX5102 $5,000,000Características MX5102 InstruccionesCircuitos de cable y de satélite MX5102 EspecificacionesCircuito telefónico Nota a LOS Instaladores Catv Instrucciones de seguridad importantesPrincipales caracterís Batería extraíble panel de acceso Operación normal de UPS MX5102 OperaciónAdvertencia de batería baja Advertencia de sobrecargaMX5102 Operación Avanzada Años de garantía Batería Información sobre la garantía