Oki 490 manual Appendix C Specifications

Page 75

Appendix C: Specifications

Note: Specifications are subject to change without notice.

Print Method

Impact dot matrix

Printhead

24 pins, 0.20 mm (0.0079") diameter, with thermal protection

Interfaces

Standard: Centronics parallel, IEEE-1284 compliant USB 1.1

Optional: RS-232C Serial

Ethernet Print Servers:

6120i 10/100 Base-TX Internal

6020e 10/100 Base-T External

6010e 10 Base-T External

Receive Buffer Size

Maximum 128K

Reliability

Ribbon Life

4 million characters, on average, 10 cpi utility

Printhead Life

200 million characters average in 10 cpi draft mode at 25% duty and 35% page density

Mean Time Between Failures (MTBF)

20,000 hours at 25% duty cycle and 35% page density

Mean Time to Repair (MTTR)

15 minutes

75

Image 75
Contents User’s Guide Mailing Address Safety Microline 490/491 User’s Guide Contents Troubleshooting Printer Features IntroductionOki Data on the Internet Internet Support Helpful HintsSaving Money Forms Tear-Off Saving TimeTurning the Platen Knob Controlling Access to the PrinterOperation Tips Top of Form TOFParts Identification Rear Feed Continuous Forms Using Your PrinterParts Identification Top Feed Single Sheets Top of Form TOF and Forms Tear-Off Top of Form TOFDetermining if Forms Tear-Off is Off or On Forms Tear-Off OFF Default Setting Setting Top of Form TOFForms Tear-Off Set to on Temporarily Changing the Top of Form Position Resetting Top of Form to the Factory DefaultPotential Problems with Software Packages Forms Tear-Off FeatureChanging the Forms Tear-Off Setting Paper ParkManual Forms Tear Off Continuous Forms toSingle Sheets Changing Paper PathsSingle Sheets toContinuous Forms Printhead Gap Print Quality Typefaces LQ Mode Character Pitch Printer Reset EmulationsChanging Emulations Menu Mode Keys Menu ModeEntering and Exiting Menu Mode Resetting the Menu to the Factory DefaultsPrinting the Menu Settings Changing the Menu Settings Group Settings Defaults are set in bold italic Menu Settings Table13.6 500 ms, 1 sec, 2 sec DEFAULT, Mode 1, Mode Invalid, Valid Menu Settings Table Explanations of Menu Items Use this to switch character sets to IBM Set Selects the printer command set emulation you want to engage Sets the signal on pin 18 to +5 volts or open Choose the quality and typeface of printing Change to Double for double width and height printing Replacing the Ribbon Cartridge MaintenancePrinthead may be HOT Rear Feed Loading PaperCareful Open the tractor covers Microline 490/491 User’s Guide Maintenance Loading Rear Feed Paper from the Front of the Printer ML490ML491 Microline 490/491 User’s Guide Maintenance Top Feed Single Sheets Maintenance Rear-Feed Paper Jams Clearing Paper JamsRear-Feed, Repeating Paper Jams Microline 490/491 User’s Guide Single-Sheet Paper Jams Cleaning the Housing General Information TroubleshootingSolution Problems / SolutionsSolutions Ink smears on the paper when I print narrow columns There are dots missing in my printouts Printer needs paper. The Alarm is not on. I can’t load paper Purchasing Parts & Accessories Appendix a Parts & AccessoriesPart Number Replacement PartsOption Part Number AccessoriesAppendix B Printer Control Codes Epson LQ CommandsDEL Enabled On DC3 Carriage Return Character Pitch, Select 10 cpi ESC % H IBM CommandsESC Q $ Appendix C Specifications Characters per Line cpl Graphics ResolutionEmulations co-resident Print SpeedResident Fonts Bar CodesResident Typefaces Paper Specifications ML490 Paper Specifications ML491 Physical Specifications Environmental RequirementsElectrical Requirements Appendix D Installation LocationUnpack Microline 490/491 User’s Guide Installation Install the Ribbon Cartridge Power Connection Computer ConnectionsParallel LPT Ieee USB Specification 1.1 Compliant Font Sample Test Testing the PrinterRolling Ascii Test Printer Drivers Hexadecimal Dump ModeLoading the OKI Driver Using a Compatible DriverIndex IBM Index Tear