Brady 2024, 2034 manual Test Label Examples, Configuration Test Label

Page 40

The Self-Test may also be initiated while the power is on by simultaneously pressing the PAUSE and CANCEL buttons. Simultaneously release them and immediately press and hold the FEED button until the ribbon/media LED flashes.

NOTE: If any configuration errors are indicated by the Self-Tests, check the Printer's dip switch settings or configuration setup.

3.3.1 Test Label Examples

The first test label printed will be the Configuration Label, this label lists the Printer's configuration and status. The following sample was produced on a standard printer without the test plugs installed.

FRI	SEPTEMBER 23, 1996 10:12 340
VER:		GA	-		1.14		01/30/96
ROM	CHECKSUMS
U13		47-2091-01P
U24		47-2090-01P
U34		47-2088-01B
U2		47-2089-01B
SYSTEM RAM CHECKS_ _ _ _ GOOD							SYSTEM RAM SIZE_ _ 512 KBYTES
SERIAL	PORT		BAUD		RATE	IS 9600			TRANSFER SWITCH IS ON
SWITCH 1		1		2	3	4	5	6	7	8
		ON		ON	ON	OFF	OFF	OFF OFF OFF
INTERNAL		1		2	3	4	5	6
		OFF		OFF	OFF	OFF	OFF	OFF
INPUT VALUES
PAPER:	255		EDGE:		253	REFL:	0 TEMP:			76
POT :	120		TOFA:		120	RIBN:	10		RWND:	0

COUNTER INFORMATION
ABSOLUTE VALUES	2-21-1996	RESETABLE VALUES	9- 5-1995
LENGTH_ _ _ _	2317 INCHES	LENGTH_ _ _ _	2317	TIME_ _ _ _
_ _	1 HOURS	TIME_ _ _ _ _ _	1 HOURS
MEMORY CONFIGURATION
INTERNAL MODULE_ _ _ _ _ _ _ _ 15		SCALABLE FONTS_ _ _ _ _ _ _ _ 0

Figure 3-4 Configuration Test Label

_______________________________________________________________________

34	Using Your Printer

Image 40

Contents Logo W.H. Brady Co Automatic Indentification Products Part Number Revision D Agency Compliance and Approvals Important Safety Instructions Contents Appendix a Introduction IntroductionMechanism Detail Technical Specifications ResolutionPrint Technology Print SpeedAdditional Options Standard Ribbon Sizes Label/Tag Media Specifications Media SpecificationsGetting Started UnpackingChecking the AC Power Requirements Selecting 230 VAC Operation Selecting 230 VACConnecting the Printer Rear Printer ConnectionsInterfacing to the Printer Interface Cable Applications Dip Switch Settings Communications Dip Switch SettingsInstallation of a Memory Cartridge Memory CartridgesMedia Access Media Loading5a Media Installation 3 core 5b Media Installation Using the Optional Internal Rewind Installing the Arc Plate for Internal rewindInstalling Media with Internal Rewind Option Using the Peel and Present Option Using the Peel and Present OptionInstalling Media using Peel and Present Option Ribbon Installation and Removal Ribbon Installation11 Ribbon Installation showing J-hook Ribbon Removal 12 Selecting Ribbon On Thermal TransferUsing Your Printer Front Control PanelOn position. This Switch is not present on LCD/Keypad Front Panel OptionPotentiometer is not present on the LCD/Keypad Front Panel OptionOptional LCD/Keypad Front Panel Optional LCD/Keypad Front PanelUsing the Optional LCD/Keypad Front Panel ShiftBasic Function Basic Function Ribbon SaverAdvanced Setup Basic Function TOF AdjustAdvanced Setup Operation Advanced Setup Maintenance Power On Self-Test Self-TestConfiguration Test Label Test Label ExamplesPrinthead Test Label Configuration Test Label Internal Dip Switch SettingsUsing Your Printer Character Dump Mode Ascii Character Dump LabelFactory Default Setup Fuse ReplacementUsing Your Printer Printing Labels Programming Commands Immediate CommandsSystem Level Commands Char Description FormatXMFname Label Formatting Commands Description Format+pii Special Label Formatting Commands Bitmapped Font Loading CommandsProgramming Example Printing Bar CodesField Example linePrinting Lines and Boxes Maintenance and Adjustments Printer Maintenance schedulesCleaning the Printhead Cleaning the Printhead Troubleshooting Printer does not print Possible cause and solutionPoor print quality Possible cause and solution Media slips or does not properly advanceOptional LCD/Keypad Front Panel Alarms LCD Display Alarm DescriptionCutter NotEQP Mechanical AdjustmentsRibsvr NotEQP Media Width Adjustment Media Width AdjustmentMedia Sensor Adjustment Media Sensor AdjustmentPrinthead Replacement RemovalReplacement Printhead RemovalMaintenance and Adjustments Appendix a Ascii Control Code Chart Char Dec HexXON = DC1XOFF = DC3 Ascii Control Code Chart Appendix B Available Fonts and Bar Codes Human-Readable Fonts Table B-1 Human-Readable Font SizesFont Valid Ascii Characters, Decimal Table B-2 Valid Human-Readable Font Ascii CharactersAppendix B Appendix B Bar Code Fonts Table B-3 Valid Bar Code Font Ascii CharactersAppendix B Barcode O Appendix B Barcode S Barcode T Barcode z Appendix B Error Codes Appendix CAppendix C Support Services Appendix DBrady Company Customer Service Form Product Service and Support Programs Appendix D Appendix E Warranty Information Thermal PrintheadWarranty Service Procedures General Warranty ProvisionsLimitation of Liability Appendix E