Wacom DTK-2400 user manual Removing Cintiq from the Display Stand

Page 92

ContentsIndex

92

REMOVING CINTIQ FROM THE DISPLAY STAND

The Cintiq interactive pen display has been specifically designed for use when mounted on the Cintiq display stand. However, there may be times when it will be necessary to remove the pen display from the stand. For example, you may want to locate the pen display on a suitable VESA mounting arm.

See using an alternate mount or stand.

Important: Request assistance from another person when removing Cintiq from the stand. Cintiq is heavy. Use care when working with or moving the unit.

To remove the pen display from the stand:

1.First disconnect all cables from between the display stand and your computer. Then move Cintiq to a location with adequate space for disassembly.

•Adjust height and incline so the display stand support arms are locked upright, with Cintiq positioned horizontally. Place all cables on top of the stand base and ensure they do not hang free. Tripping over loose cables can cause physical damage or personal injury.

•Request assistance from another person or persons. Each person should securely grasp the lower part of a display support arm near the display stand base. With the other hand, grasp the base of the stand at the front corner. Using care, lift and carefully move this product while supporting the base of the stand.

Important: The assembly is heavy. Do not attempt to lift Cintiq by yourself. Each person should use both hands to securely grasp the product. Grasp the stand base at the corner areas to avoid any sharp edging. DO NOT lift the display unit itself, otherwise damage might occur to the LCD if it flexes during movement. Also, the display unit does not have sufficient strength to support the load of the stand hanging freely from it. Work together, and lift carefully.

•Locate Cintiq on a desktop or other working surface that is flat, clean, and free of any moisture or oily film. Taking care not to pinch your fingers, do this by first placing the rear half portion of the stand onto the table surface. Then slide the stand fully into place so that it will not tip or fall.

•When in place, use the incline levers to rotate the display back to a vertical position.

ContentsIndex

92

Image 92

Contents User’s manual ContentsIndex Table of Contents Glossary About the Manual TopicUnpacking Your Cintiq Unpacking Your ProductContentsIndex BOX Contents ContentsIndex Setting UP Your Cintiq System RequirementsHardware Installation DVI-I DVI-DCintiq cabling diagram ContentsIndex Software Installation PEN Display Features Getting to Know Your CintiqFront View Use for adjusting the display settings Rear ViewPEN Features Using the Cintiq Display Stand Display Stand Features See hardware installationDisplay Stand Location ContentsIndex Readjust the pen display height and incline as needed Adjusting Display Height and Incline ContentsIndex Using a Keyboard with Cintiq Cable Replacement DisplayPort DVI-I to DVI-D Dual-Link Power Install or replace a cable by reversing this procedure Setting UP Your Work Area Working with Your CintiqContentsIndex Configuring Cintiq for Handedness Using the Grip PEN Holding the PENPositioning ClickingWorking with Pressure Sensitivity Using the Side SwitchDragging Drawing with Tilt ErasingPEN Display Controls Using the Hardware Control Buttons Using the Expresskeys Using the Touch Rings Working with Multiple Monitors Adjusting the Display Factory PRESETS, AUTO-SYNC, and User SettingsOn Screen Display OSD Settings Button FunctionContentsIndex Power Saving ConsumptionCustomizing Your Cintiq Opening the Control PanelControl Panel Overview Displays advanced optionsSee also working with multiple tools Calibrating the PEN Display Customizing the PEN Adjusting TIP Feel and DOUBLE-CLICK Adjusting Eraser Feel Advanced TIP and Eraser Pressure SettingsCustomizing Tool Buttons Customizing PEN Display Functions Customizing Tilt SensitivityCustomizing the Expresskeys See using the Touch Rings for more information Customizing the Touch RingsButton Functions Function Name DescriptionImportant Because the Enter Windows and Return Mac keys Choose from OPEN/RUN Strokes Mouse mode Function Name Using and Customizing the Radial Menu Working with Display Toggle APPLICATION-SPECIFIC Settings Removing APPLICATION-SPECIFIC Settings Creating AN APPLICATION-SPECIFIC SettingChanging APPLICATION-SPECIFIC Settings Working with Multiple Tools Changing the Tablet Mode Troubleshooting Try testing CintiqTesting Cintiq Testing Controls and Input Tools Testing the Hardware Control ButtonsTesting the Expresskeys Testing the Touch RingsTesting a PEN Display Troubleshooting General Display ProblemsContents Index VGA Problems PEN Tablet Troubleshooting General ProblemsControls and input tools Contents Index ContentsIndex WINDOWS-SPECIFIC Problems MAC-SPECIFIC Problems See technical support optionsContentsIndex Technical Support Options Obtaining Driver Downloads Frequently Asked Questions See managing preferences Care and Maintenance Caring for CintiqReplacing the PEN NIB Other Useful Information Removing Cintiq from the Display Stand ContentsIndex ContentsIndex Mounting Cintiq on the Display Stand ContentsIndex ContentsIndex Using AN Alternate Mount or Stand See removing Cintiq from the display standUninstalling Cintiq Managing Preferences Installing Multiple Tablets Using Applications Integrated for Tablet Control Importing Expert Settings PEN and Digital INK Capabilities in Windows Product Information 105Ordering Parts and Accessories Available Parts and AccessoriesGlossary 108 109 Index 111 112 Wacom International Offices Wacom Technology Corporation Wacom Europe Gmbh