Toshiba BSX4TGS20QMR, B-SX4T Series owner manual 3517, Test Print

Page 24

2. PRINTER SETUP

ENGLISH VERSION EO1-33034

2.10 Test Print

2.10 Test Print

NOTES:

1.Select the sensor type which matches the media being used. Basically, the Reflective Sensor (Black Mark Sensor) is for tag paper, and the Transmissive Sensor (Feed Gap Sensor) is for labels.

2.Select the print mode which matches the media being used. Basically, the thermal transfer is with ribbon, and the thermal direct is without ribbon.

A print test should be performed to check that the printer is operating correctly.

The following paragraphs guide you through the diagnostic procedure for test label printing. Please follow the step-by-step procedures exactly for

 

following￿￿!',$*message.￿ ￿￿￿$

best results.

 

 

 

1.

Use label stock for the test print. For best results, use labels that are

 

76 mm or longer in length.

2.

Press and hold the [FEED] and [PAUSE] keys while turning on the

 

printer power switch. The LCD Message Display will show the

3.

appear￿￿!7(67.

3517

 

Press the

[FEED] key three times to advance to the test print mode as

 

35,17&21',7,21

 

 

indicated￿￿!7(67by

35,17the following message in the LCD Message Display.

4.

￿￿!76735,17

 

Press the

[PAUSE] key and the print condition setting display will

5.

,668(

&2817

￿

Press the

[PAUSE]

key and the issue count setting display will

 

35,1763(('￿¥￿V

 

appear. Set the issue count with the [FEED] or [RESTART] key.

6.

Press the

[PAUSE] key and the print speed setting display will

 

appear.￿￿!7(67Set the35,17print speed with the [FEED] or [RESTART] key.

7. Press the [PAUSE] key and the sensor type setting display will appear￿￿￿￿6(16257!7(6735,17!7(673,7. Select5$the16sensor￿ type with the [FEED] or [RESTART] key.

8. Press3577<3(the [PAUSE]75$16)5key and the print mode setting display will appear. Select the print mode with the [FEED] or [RESTART] key.

E2-14

Page 23 Page 25
Image 24
Page 23 Page 25
Contents SX4T Series CE Compliance for EU only VorsichtWkhsoxj Precautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer GoriConnecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionBatch mode Strip modeSTANDARD/PEEL OFF position Build-in rewinder mode Cut modeLoading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards 3517 Test Print$5&2 Test Print Sample of the bar code test print label On Line Mode Operation PanelOperation Reset Dump Mode Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Care/Handling of the Media and Ribbon Optional Cutter ModuleTroubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print HeadThreshold Setting Threshold setting procedureAppendix 1 Specifications A1.1 PrinterModel A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor LabelA1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaTag paper with square holes A1.4 Ribbon Figure below shows the effective print area on the mediaSymbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 Print Samples Interleaved 2 CODE39 Standard JAN13, EAN13EAN13+2 digits EAN13+5 digits CODE39 Full AsciiUPC-A+5 digits Industrial 2RSS-14 RSS-14 Stacked RSS LimitedGlossaries Bar codePrint head element USB Universal Serial BusIndex Index Page EO1-33034B
Top Page Image Contents