Toshiba B-SX4T Series, BSX4TGS20QMR owner manual Product Overview, Introduction Features, Unpacking

Page 7

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33034

1.1 Introduction

1. PRODUCT OVERVIEW

1.1 Introduction

Thank you for choosing the TEC B-SX4T series thermal printer. This Owner’s Manual contains from general set-up through how to confirm the printer operation using a test print, and should be read carefully to help gain maximum performance and life from your printer. For most queries please refer to this manual and keep it safe for future reference. Please contact your TOSHIBA TEC representative for further information concerning this manual.

1.2 Features

This printer has the following features:

∙The print head block can be opened providing smooth loading of media and ribbon.

∙Various kinds of media can be used as the media sensors can be moved from the centre to the left edge of the media.

∙When the optional interface board is installed, Web functions such as remote maintenance and other advanced network features are available.

∙Superior hardware, including the specially developed 8 dots/mm (203 dots/inch) thermal print head which will allow very clear print at a printing speed of 76.2 mm/sec. (3 inches/sec.), 152.4 mm/sec. (6 inches/sec.), or 254.0 mm/sec. (10 inches/sec.).

∙Besides the optional Cutter Module, there is also an optional Strip Module, Ribbon Saving Module, PCMCIA Interface Board, Expansion I/O Interface Board, LAN Interface Board, and the USB Interface Board.

1.3 Unpacking

NOTES:

1.Check for damage or scratches on the printer. However, please note that TOSHIBA TEC shall have no liability for any damage of any kind sustained during transportation of the product.

2.Keep the cartons and pads for future transportation of the printer.

Unpack the printer as per the Unpacking Instructions supplied with the printer.

E1- 1

Page 6 Page 8
Image 7
Page 6 Page 8
Contents SX4T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Cut mode Build-in rewinder modeLoading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Test Print Sample of the bar code test print label Operation Panel On Line ModeOperation Reset Dump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonRestart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingA1.1 Printer Appendix 1 SpecificationsModel Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples CODE39 Full Ascii Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digits EAN13+5 digitsRSS Limited UPC-A+5 digitsIndustrial 2 RSS-14 RSS-14 StackedBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page EO1-33034B
Top Page Image Contents