Toshiba B-SX4T Series, BSX4TGS20QMR A1.2 Options, A1.3 Media, A1.3.1 Media Type, Label, Tag paper

Page 39

APPENDIX 1 SPECIFICATIONS

ENGLISH VERSION EO1-33034

 

A1.2 Options

 

 

A1.2 Options

Option Name

Type

Description

Swing cutter module

B-4205-QM

A stop and cut swing cutter.

Rotary cutter module

B-8204-QM

Rotary cutter

Strip module

B-9904-H-QM

This allows use of on-demand (peel-off) operation or to take-up

 

 

labels and backing paper together when using the rewind guide

 

 

plate. To purchase the strip module, please inquire at your local

 

 

distributor.

Ribbon saving

B-9904-R-QM

This module moves the print head up and down by using a

module

 

solenoid to minimise ribbon usage as far as possible.

Expansion I/O

B-7704-IO-QM

Installing this board in the printer allows connection to an

interface board

 

external device with the exclusive interface.

PCMCIA interface

B-9700-PCM-QM

This board enables the use of the following PCMCIA cards.

board

 

LAN card: 3 COM 3CCE589ET (recommended)

 

 

ATA card: Conforming to PC card ATA standard

 

 

Flash memory card: 1MB and 4MB cards (See Section 2.9.)

Built-in LAN

B-9700-LAN-QM

This board enables the printer to be used in a LAN network.

interface board

 

 

USB interface board

B-9700-USB-QM

Installing this board enables a connection to a PC which has a

 

 

USB interface.

NOTE:

To purchase the optional kits, please contact the nearest authorised TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.

A1.3 Media

Please make sure that the media being used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC.

For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative.

A1.3.1 Media Type

Two types of media can be loaded for this thermal transfer and direct thermal printer: label or tag. The table below shows size and shape of the media available for this printer.

Stop position

Cut position

 

Black Mark

 

Black Mark

Label

(on reverse side) Refer to

Tag paper

(on reverse side)

NOTED3 below.

 

k

 

positionStop k

 

 

 

C?

D

 

 

Cut position

 

 

 

@

 

 

 

A

?

j

E

 

 

 

 

E

 

 

B

Feed Direction

 

 

A

 

 

 

 

EA1- 2

 

Image 39
Contents SX4T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Introduction Features Product OverviewUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionBatch mode Strip modeSTANDARD/PEEL OFF position Cut mode Build-in rewinder modeLoading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Test Print Sample of the bar code test print label Operation Panel On Line ModeOperation Reset Dump Mode Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonRestart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingAppendix 1 Specifications A1.1 PrinterModel Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples CODE39 Full Ascii Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digits EAN13+5 digitsRSS Limited UPC-A+5 digitsIndustrial 2 RSS-14 RSS-14 StackedBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page EO1-33034B