Toshiba B-SX4T Series, BSX4TGS20QMR owner manual Threshold Setting, Threshold setting procedure

Page 37

5. TROUBLESHOOTING

ENGLISH VERSION EO1-33034

5.4 Threshold Setting

5.4 Threshold Setting

NOTES:

1.If the [PAUSE] key is released within 3 seconds while in the pause state, the paper will not feed.

2.Failure to feed more than 1.5 labels may result in an incorrect threshold setting.

3.While the Print Head Block is raised, the [PAUSE] key does not work.

4.A paper end error cannot be detected during paper feed.

5.Selecting the Transmissive Sensor (for pre-printed labels) within software commands allows the printer to detect the proper print start position even when using pre-printed labels.

6.If using the Transmissive Sensor and the printer continues to print out of position even after setting the threshold, contact a TOSHIBA TEC service representative.

o maintain a constant print position the printer uses the Transmissive Sensor to detect the gap between labels by measuring the amount of light passing through the media. When the media is pre-printed, the darker %21/,1((or￿6;more￿7dense) 9inks￿￿￿can$interfere with this process causing paper jam errors. To get around this problem a minimum threshold can be set for the sensor in the following way.

T

 

Threshold setting procedure

1.

%￿6;￿7

9￿￿￿$

 

Turn the power ON. The printer is in stand by mode.

2.

state75. $160,66,9(

 

 

 

Load a pre-printed media roll.

 

%￿6;￿7

9￿￿￿$

 

3.

Press3$the86([PAUSE] key.

 

4.

The printer enters the pause mode.

5.

Press and hold the [PAUSE] key for at least 3 seconds in the pause

 

%￿6;￿7

9￿￿￿$

Black mark sensor

6.

75$160,66,9(

 

 

Feed gap sensor

The sensor type is displayed.

 

 

%￿6;￿7

9￿￿￿$

 

7.

Select5()/(&7,9(the sensor to be adjusted by pressing the [FEED] key.

 

 

 

 

 

 

 

 

[FEED]

key

 

 

 

 

 

 

 

9￿￿￿$

 

8.

%￿6;￿7

 

Press and hold the

[PAUSE] key until more than 1.5 labels (tags)

 

have been issued.

9￿￿￿$

 

 

%￿6;￿7

 

 

The media will continue to be fed until the [PAUSE] key is

 

released. (Threshold setting for the selected sensor is completed by

 

this3operation.)$86(

9￿￿￿$

 

 

%￿6;￿7

 

9.

Press21the/,1([RESTART] key.

 

10.

The printer is in stand-by.

 

11.

Send21an/,1(issue command from the PC to the printer.

E5- 4

Image 37
Contents SX4T Series Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionStrip mode Batch modeSTANDARD/PEEL OFF position Cut mode Build-in rewinder modeLoading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards Test Print 3517$5&2 Test Print Sample of the bar code test print label Operation Panel On Line ModeOperation Reset Dump Mode Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Care/Handling of the Media and RibbonError Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingA1.1 Printer Appendix 1 SpecificationsModel A1.3 Media A1.2 OptionsA1.3.1 Media Type LabelLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples JAN13, EAN13 Interleaved 2 CODE39 StandardEAN13+2 digits EAN13+5 digits CODE39 Full AsciiIndustrial 2 UPC-A+5 digitsRSS-14 RSS-14 Stacked RSS LimitedBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page EO1-33034B