APPENDIX 2 MESSAGES AND LEDS
ENGLISH VERSION
APPENDIX 2 MESSAGES AND LEDS
APPENDIX 2 MESSAGES AND LEDS
Appendix 2 describes the LCD messages displayed on the operation panel.
Symbols in the message
1:•: The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2:****: the number of unprinted media. Up to 9999 (in pieces)
3:%%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4:###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5:&&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
|
| LED Indication |
| Restoration by Acceptance of | ||
|
|
|
|
| Status Request | |
No. | LCD Message | Printer Status | RESTART key | |||
Reset Command | ||||||
|
| POWER ONLINE ERROR |
| Yes/No | ||
|
|
| Yes/No | |||
|
|
|
| |||
|
|
|
|
| ||
1 | ON LINE |
| • | • | z | In online mode | Yes | |
ON LINE |
| • | ~ | z | In online mode (The printer in | Yes | ||
|
| communication) |
|
| ||||
2 | HEAD OPEN |
| • | z | z | The print head block is opened in online | Yes | |
| mode. |
|
| |||||
3 | PAUSE **** |
| • | z | z | The printer is paused. | Yes | Yes |
4 |
|
|
|
|
| A parity, overrun, or framing error has | Yes | Yes |
COMMS ERROR | • | z | • | occurred during communication through |
|
| ||
|
|
|
|
|
| the |
|
|
5 | PAPER JAM | **** | • | z | • | The media is jammed during paper feed. | Yes | Yes |
6 | CUTTER ERROR**** | • | z | • | A problem has occurred with the cutter | Yes | Yes | |
module. |
|
| ||||||
7 | NO PAPER | **** | • | z | • | The media has run out, or the media is | Yes | Yes |
not loaded properly. |
|
| ||||||
8 | NO RIBBON | **** | • | z | • | The ribbon has run out. | Yes | Yes |
9 | HEAD OPEN | **** | • | z | • | Feed or printing was attempted with the | Yes | Yes |
print head block open. |
|
| ||||||
10 | HEAD ERROR | • | z | • | There is a problem with the print head. | Yes | Yes | |
11 | EXCESS HEAD TEMP | • | z | • | The print head is overheated. | No | Yes | |
|
|
|
|
|
| The ribbon has been torn. A problem | Yes | Yes |
12 | RIBBON ERROR**** | • | z | • | has occurred with the sensor that |
|
| |
determines the torque for the ribbon |
|
| ||||||
|
|
|
|
|
| motor. |
|
|
13 | REWIND FULL **** | • | z | • | An overflow error has occurred in the | Yes | Yes | |
rewinder unit. |
|
| ||||||
14 | SAVING%%%%%%% |
|
|
| In writable character or PC command | Yes | ||
or |
| • | • | z | save mode |
|
| |
| SAVING ###&&&& |
|
|
|
|
|
| |
15 | FLASH WRITE ERR. | • | z | • | An error has occurred while writing to | No | Yes | |
flash memory or ATA card. |
|
| ||||||
16 |
|
|
|
|
| An erase error has occurred in | No | Yes |
FORMAT ERROR | • | z | • | formatting the flash memory or ATA |
|
| ||
|
|
|
|
|
| card. |
|
|
17 | FLASH CARD FULL | • | z | • | Data cannot be stored because the flash | No | Yes | |
memory or ATA card is full. |
|
| ||||||
18 | Display of error | • | z | • | A command error has occurred in | Yes | Yes | |
| message (See Notes.) |
|
|
| analyzing the command. |
|
| |
19 | POWER FAILURE | • | z | • | A power failure has occurred. | No | No | |
20 | INTIALIZING… | • | z | z | A flash memory card is being initialised. | |||
21 | 100BASE LAN | • | z | z | 100 Base LAN Board is being | |||
| INITIALIZING… |
|
|
| initialized. |
|
| |
EA2- 1