Toshiba KD-1025 manual Description of Operations, From power on to ready, Ready status

Page 14

3.2Description of Operations

[A]From power ON to ready

(1)When the equipment is turned ON, the power is also supplied to the feeder unit. And when the power is supplied, the feeder unit detects and judges the clock frequency output from the LGC board on the equipment to control transport speed of the unit.

(2)After that, the tray-up motor (M2)/(M3) is turned ON to raise the corresponding tray. When the tray-up sensor (S4)/(S5) is turned ON correspondingly, the tray-up motor (M2)/(M3) is turned OFF to stop the tray. If the empty sensor (S6)/(S7) is OFF (H) at this time, it is judged that there is no paper in the drawer. If the empty sensor is ON (L), it is assumed that there is paper in the drawer, and the tray stays in the raised position until the drawer is pulled out.

(3)If the power is turned ON when the drawer has been pulled out, the tray-up motor for that drawer is not turned ON. The tray is raised as soon as the drawer is installed, and it detects if there is paper in the drawer.

(4)If either of the drawer feed sensors (S2), (S3) is ON (there is paper in the transport path) when the power is turned ON, that means paper jam has occurred and operation is disabled until the paper is removed.

[B]Ready status

(1)Trays detect the paper as described above, and the equipment goes into ready status.

(2)The tray goes down automatically when the drawer is removed and it is raised as soon as the drawer is installed again and checks if there is paper in the drawer.

[C]From the start to the end of copying

(1)When the [START] button is pressed, the feed/transport and exit motors of the equipment and the PFP motor (M1) are turned ON at the same time.

(2)When the equipment judges that PFP is ready for feeding paper, it turns ON the feed clutch (CLT2)/(CLT3) of the selected drawer. This clutches drive the pickup roller and feed roller to feed paper from the tray.

(3)When the drawer feed sensor (S2)/(S3) comes ON, the transport clutch (CLT1) is turned ON to drive the PFP transport roller.

(4)A fixed time after the drawer feed sensor (S2)/(S3) comes ON, the feed clutch (CLT2)/(CLT3) is turned OFF and feeding from the drawer is completed.

(5)The paper is transported to the equipment by the PFP transport roller. A fixed time after the leading edge of the paper reaches the drawer feed sensor (S2), if the trailing edge of the previously sent sheet still remains at the copier feed sensor, the transport clutch (CLT1) is turned OFF to stop the transport of the paper.

(6)A fixed time after the paper turns the resist clutch ON, PFP becomes ready for feeding the next sheet of paper, and the procedures (1) to (5) are repeated.

(7)When the copying operation is completed, the feed/transport motor, exit motor, PFP motor (M1), and transport clutch(CLT1) are turned OFF and the transport roller is stopped.

KD-1025

© 2009 - 2011 TOSHIBA TEC CORPORATION All rights reserved

GENERAL OPERATION

 

3 - 2

Image 14
Contents KD-1025 Trademarks General Precautions for INSTALLATION/SERVICING/ Maintenance Page Contents Contents Specifications KD-1025Specifications Overview Front Sectional ViewLayout of Electrical Parts CLT3 CLT1 M3 PWBElectrical Parts MotorOverview General Operation Driving System and Feeding OperationReady status From power on to readyDescription of Operations From the start to the end of copyingJam detection Error DetectionCall for Service Flow Chart Upper drawer feedingON? General Operation Drawers Disassembly and ReplacementInstallation and Removal of Drawers and Covers Drawer coverStabilizer cover Rear coverSide cover Feeding side front coverFeeding side rear cover Block PFP board PWB Upper/Lower Transport Rollers Upper transport rollerLower transport roller Remove the coupling, pin, and clip Bracket Motor Upper drawer tray-up motorLower drawer tray-up motor Protrusion PFP motor assembly PFP motorRemove 1 connector and take off the PFP motor assembly Separation roller Feed/Separation/Pickup RollerDrawer feeding unit Feed roller Pickup rollerDrawer feed clutch CLT2/CLT3 Paper stock sensor S10/S11 Switches and SensorsTray-up sensor S4/S5/paper empty sensor S6/S7 Side cover open/close switch S1 Upper/lower drawer feed sensor S2/S3Upper/lower drawer detection switches S8/S9 Drawer detection switchDiagram5.1 Harness IRCUITC5. ElectricCircuit Diagram Electric Circuit Equipment PC Board Electric Circuit Periodic Maintenance Symbols used in the checklistApply grease On the inside entirely Lever Separation roller Ver.01 Revision RecordVer.02 Revision Record