Toshiba KD-1025 manual Specifications

Page 7

1.SPECIFICATIONS

Item

KD-1025

Appearance

Feeding method

Automatic feeding: 1 drawer installed from the front

Paper

Size: A3, B4, A4, A4-R, B5, B5-R, A5-R, LD, LG, LT, LT-R, 8K, 16K, 16K-R, FOLIO,

 

COMPUTER, 13"LG, 8.5"x8.5"

 

Thickness: 64 g/m2 to 105 g/m2 (17 lb. Bond to 94.5 lb. Cover)

Capacity of drawer

Stack height: 60.5 mm (Approx. 550 sheets: 80 g/m2 (22 lb. Bond))

Dimensions

575 (W) × 583 (D) × 292 (H) mm

 

22.64 (W) × 22.95 (D) × 11.50 (H) inch

 

(Height - Floor to top of the front cover)

 

660 (W) × 701 (D) × 292 (H) mm

 

25.98 (W) × 27.60 (D) × 11.50 (H) inch

 

(Including the stabilizer cover)

Weight

Approx. 21 kg (46.3 lb.)

 

 

Power supply

5 V, 24 V (supplied from the equipment)

 

 

Accessory

Unpacking Instructions (1)

 

Connecting plates (4)

 

Screws for connecting plates (6)

 

Fixing screw for ground wire (1)

 

Paper size indicator sheets (2)

 

Stabilizer brackets (4)

 

Feeding side stabilizer foot (1)

 

Screw for feeding side stabilizer foot (1)

 

Rear side stabilizer covers (2)

 

Front side stabilizer cover (1)

 

Screws for stabilizer (4)

 

 

Option

Drawer module: MY-1033

 

(With this option, 2 drawers become available for feeding).

Note:

This manual explains on the premise that 2 drawers are available (that is, the optional drawer module is installed).

1

© 2009 - 2011 TOSHIBA TEC CORPORATION All rights reserved

KD-1025

 

SPECIFICATIONS

1 - 1

Image 7
Contents KD-1025 Trademarks General Precautions for INSTALLATION/SERVICING/ Maintenance Page Contents Contents KD-1025 SpecificationsSpecifications Front Sectional View OverviewCLT3 CLT1 M3 PWB Layout of Electrical PartsMotor Electrical PartsOverview Driving System and Feeding Operation General OperationFrom the start to the end of copying From power on to readyDescription of Operations Ready statusCall for Service Error DetectionJam detection Upper drawer feeding Flow ChartON? General Operation Drawer cover Disassembly and ReplacementInstallation and Removal of Drawers and Covers DrawersRear cover Stabilizer coverFeeding side rear cover Feeding side front coverSide cover Block PFP board PWB Upper transport roller Upper/Lower Transport RollersLower transport roller Remove the coupling, pin, and clip Bracket Upper drawer tray-up motor MotorLower drawer tray-up motor Protrusion PFP motor PFP motor assemblyRemove 1 connector and take off the PFP motor assembly Drawer feeding unit Feed/Separation/Pickup RollerSeparation roller Pickup roller Feed rollerDrawer feed clutch CLT2/CLT3 Tray-up sensor S4/S5/paper empty sensor S6/S7 Switches and SensorsPaper stock sensor S10/S11 Upper/lower drawer feed sensor S2/S3 Side cover open/close switch S1Drawer detection switch Upper/lower drawer detection switches S8/S9IRCUITC5. Electric Diagram5.1 HarnessCircuit Diagram Electric Circuit Equipment PC Board Electric Circuit Symbols used in the checklist Periodic MaintenanceApply grease On the inside entirely Lever Separation roller Ver.02 Revision RecordVer.01 Revision Record