Toshiba G8000 operation manual UPS Specifications, General Specification, Mechanical Specification

Page 45

12 UPS Specifications

12.1General Specification

Terms

Specification

Remarks

Conforming Standard

UL1778-2001

UL, cUL, IEC

Ambient Temperature

32 – 104 °F (0 – 40 °C)

 

Relative Humidity

30% – 90%

Non-condensing

Altitude

< 3,280 ft (< 1,000 m)

Contact Toshiba Technical Support for

 

instalation above 3280 ft. (1000 m)

 

 

Audible Noise

68dB(150 kVA)

1m (39”) away from front

Insulation Resistance

3 MΩ

With 500 V-Megger

 

AC 2 kV – 1 min.

Main Circuit

Insulation Breakdown

AC 1.5 kV – 1 min.

External Interface

 

AC 500 V – 1 min.

Control Circuit

12.2Mechanical Specification

Rated Capacity

100kVA

Cabinet

 

Protection

IEC298 IP20*

Conformity

 

Exterior Paint

Sherwin Williams, HHT2-7055, 079 Beige Texture

 

FRONT: 1/16 in. (1.6mm)

Panel Thickness

BACK/SIDE/TOP: 3/64 in. (1.2mm)

 

BOTTOM: 1/8 in. (3.2mm)

Input/Output

BOTTOM

Cabling Entrance

 

Ground/Control

BOTTOM

Wiring Entrance

 

Outline

W: 36.8 in. (935 mm)

D: 31.8 in. (808 mm)

Dimension

H: 79.2 in. (2,012 mm)

 

Unit Weight

2006 lb (1000 kg))

Shipping Weight

2096 lb (1041.4 kg)

Floor Loading

2446 lbs/ft2

Per Footprint

(13,126 kg/m2)

 

FRONT: 43 7/16 in. (1,100 mm)

Clearance

BACK/SIDE: 0 in. (0 mm)

 

TOP: 15 3/4 in. (400 mm)

Heat Rejection

27,620 BTU/h

(6,960 kcal/h)

 

*IP20: Foreign objects that are 12mm (15/32”) or larger are prevented from entering the enclosure of the UPS.

G8000 Series with Isolated Output Installation and Operation Manual

37

Image 45
Contents G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International CorporationTable of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction General Safety Instructions SymbolsProhibited Symbol indicates do not take action Qualified Personnel Signal WordsFactory Authorized Personnel Important Safety InstructionsDisclaimer Safety PrecautionsKeep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright positionAvoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its sideInspection/Storage Installation Precautions Install the UPS in a controlled environmentKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on itEnvironment standard Installation PrecautionsPage Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screwsFor 100 and 150 kVA GND 150kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions150kVA UPS Exterior Dimensions Inches Do not expose the unit to vibration or shock exceeding 0.5G Transporting8.5 show examples of acceptable and unacceptable operations Transporting By CraneTransporting UPS by Forklift Transporting By ForkliftStorage/Operating Environment Operating PrecautionsPage Maintenance Precautions Qualified Personnel onlyQualified Personnel shall Disposal Do not dispose of the batteries in a fireDo not open or mutilate the batteries Installation UPS Clearance UnpackingAnchor Bolts Breaker UPS WiringAC Input Bypass Input AC Output Battery Terminal Blocks, Terminal Bus, and Power CablesBlock Number Cable Size Tightening Torque 100 KVA 150 KVA Bottom Cable Knockout Plates 100 kVA External BreakersBe sure to ground the UPS as specified Grounding WireSignal Name Operation Control WiresConnection Between UPS, Battery Cabinet & Bypass Breaker Jumper Cable Between the Neutral Terminal & Ground BUS Grounding ConfigurationUPS Specifications General SpecificationMechanical Specification Rated Capacity 150kVA Do not open the front cover Electrical SpecificationUPS may not respond if the button press is too short Operator InterfaceGraphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and ButtonsGraphic display Panel LCD/LED INDICAtors 13.2 LCD/LED IndicatorsName Description LCD IndicatorsAC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50%BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM09-09-06 Fault DisplayAbbreveations LCD ScrollOperating the UPS Epo and Control Power supply operating switchesOperation Types Pre-operational CheckPerform the pre-operational check before operating the UPS Step Startup ProceduresAC Vo 208 AC Io 50% Bypass LED is on Switch Power Supply UPS→BypassStop DC-V 0 BATT-V 0 BATT-I 0 a Complete ShutdownMake sure that the Float Charge LED is on Changing Between Float Charge and Equalize ChargeMake sure that the Batt FAULT1 warning goes away Troubleshooting Emergency Power Off EPOTypes of Errors 09-09-06 Faults and Warnings Data ScreenFault Display LCD Fault & Warning DisplaysOver Heat Fault MessagesAC O/P UV Button functions LCD Scroll w/ faults or warningsRestoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division
Related manuals
Manual 80 pages 62.95 Kb Manual 1 pages 30.84 Kb