Toshiba EO1-33088, B-EV4D SERIES owner manual Turning OFF the Printer

Page 14

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.4 Connecting the Cables to the Printer

2.3.2Turning OFF the Printer

CAUTION!

1.Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer.

2.Do not turn off the printer power while the Green Indicator Lamp is flashing as this may cause damage to the data being downloaded.

1.Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing.

2.To turn OFF the printer power press the power switch as shown in the diagram below. Note that ( { ) is the power OFF side of the switch.

Power Switch

E2- 3

Image 14

Contents TOSHIBA Barcode Printer B-EV4D SERIESOwner’s Manual VORSICHT N258CE Compliance for EU only Safety Summary Safety SummaryMeanings of Each Symbol Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWGLOSSARIES APPENDIX 2 INTERFACEEA2-1 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessWhen purchasing the power cord As of August1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To close the Top Cover 2.6 Opening/Closing the Top CoverTo open the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll 2.8.1 Media Sensor Calibration 2.8 Media SensorTest, and Dump Mode different type Utilities Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-16„ Removing an SD Card 2.9 How to Use an SD Card„ Inserting an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.3 Cover 3.1.4 Media Housing3.1.2 Platen/Sensors 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide SolutionsStatus 4.2 Status LampColor 4.3 Removing Jammed Media B-EV4D-GS14-QM-R APPENDIX 1 SPECIFICATIONSA1.1 Printer B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameUnit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Black Mark A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaRS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088