Toshiba EO1-33088, B-EV4D SERIES owner manual N258, CE Compliance for EU only, Vorsicht

Page 2
CE Compliance (for EU only)

CE Compliance (for EU only)

This product complies with the requirements of EMC and Low Voltage Directives including their amendments.

VORSICHT:

Maschinenlärminformations-Verordnung 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß EN ISO 7779.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by manufacturer for compliance could void the user’s authority to operate the equipment.

(for USA only)

“This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.”

“Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.”

(for CANADA only)

The EA10953 AC adapter should be exclusively used for the B-EV4D Series printer. The B-EV4D Series printer must be powered by the EA10953 AC adapter.

N258

Centronics is a registered trademark of Centronics Data Computer Corp.

Windows is a trademark of Microsoft Corporation.

The following information is for EU-member states only: Disposal of products

(based on EU-Directive 2002/96/EC,

Directive on Waste electrical and electronic equipment – WEEE)

The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and has to be collected separately. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centers.

The black bar indicates that the product was placed on the market after August 13, 2005.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environmental and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about the take-back and recycling of this product, please contact your supplier where you purchased this product.

< For EU Only >

TOSHIBA TEC Europe Retail Information Systems S.A. Rue de la Célidée 33 BE-1080 Brussels

Copyright © 2008

by TOSHIBA TEC CORPORATION All Rights Reserved

570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

Image 2
Contents TOSHIBA Barcode Printer B-EV4D SERIESOwner’s Manual VORSICHT N258CE Compliance for EU only Safety Summary Safety SummaryMeanings of Each Symbol Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWGLOSSARIES APPENDIX 2 INTERFACEEA2-1 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessWhen purchasing the power cord As of August1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To close the Top Cover 2.6 Opening/Closing the Top CoverTo open the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll 2.8.1 Media Sensor Calibration 2.8 Media SensorTest, and Dump Mode different type Utilities Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-16„ Removing an SD Card 2.9 How to Use an SD Card„ Inserting an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.3 Cover 3.1.4 Media Housing3.1.2 Platen/Sensors 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide SolutionsStatus 4.2 Status LampColor 4.3 Removing Jammed Media B-EV4D-GS14-QM-R APPENDIX 1 SPECIFICATIONSA1.1 Printer B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameUnit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Black Mark A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaRS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088