Toshiba EO1-33088, B-EV4D SERIES owner manual Removing Jammed Media

Page 34

4.3 Removing Jammed Media

4. TROUBLESHOOTING

ENGLISH VERSION EO1-33088

4.3 Removing Jammed Media

Flashing speed of the LED

Status	Flashing interval
Flashing slowly	1 sec.
Flashing at medium speed	0.5 sec.
Flashing fast	0.2 sec.

4.3 Removing Jammed Media

This section describes in detail how to remove jammed media from the printer.

CAUTION!

Do not use any tool that may damage the print head.

1.Turn the power off.

2.Open the Top Cover and remove the media roll.

3.Remove the jammed media from the printer. DO NOT USE any sharp implements or tools as these could damage the printer.

4.Clean the Print Head and Platen, then remove any further dust or foreign substances.

5.Load the media again, and close the Top Cover.

E4- 3

Image 34

Contents Owner’s Manual B-EV4D SERIESTOSHIBA Barcode Printer CE Compliance for EU only N258VORSICHT Meanings of Each Symbol Safety SummarySafety Summary Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWEA2-1 APPENDIX 2 INTERFACEGLOSSARIES 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessWhen purchasing the power cord As of August1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View1.5.3 Rear View Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3 Turning the Printer ON/OFF 2.2 Procedure before Operation2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll Test, and Dump Mode different type Utilities 2.8 Media Sensor2.8.1 Media Sensor Calibration Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-16„ Inserting an SD Card 2.9 How to Use an SD Card„ Removing an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.2 Platen/Sensors 3.1.4 Media Housing3.1.3 Cover 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide SolutionsColor 4.2 Status LampStatus 4.3 Removing Jammed Media A1.1 Printer APPENDIX 1 SPECIFICATIONSB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameA1.3.2 Detection Area of the Transmissive Sensor A1.3.1 Media Type ContUnit mm inch A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaInterface Cables APPENDIX 2 INTERFACERS-232C Cable description GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088