Toshiba B-EV4D SERIES Appearance, Dimensions 1.5.2 Front View, Rear View, Product Overview

Page 9

1.5 Appearance

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33088

1.5 Appearance

1.5 Appearance

1.5.1 Dimensions

1.5.2 Front View

The names of the parts or units introduced in this section are used in the following chapters.

198 (7.8)

258 (10.2)

173

(6.8)

Dimensions in mm (inches)

STATUS Lamp

Media View Window

FEED Button

Top Cover

Release Button

Media Outlet

SD Card Slot

1.5.3 Rear View

Fanfold paper slot

Ethernet interface

USB Interface

Connector

Parallel Interface

Connector (Centronics)

Power Switch

Power Jack

Serial Interface Connector (RS-232C)

E1- 3

Image 9

Contents B-EV4D SERIES Owner’s ManualTOSHIBA Barcode Printer N258 CE Compliance for EU onlyVORSICHT Safety Summary Meanings of Each SymbolSafety Summary Request Regarding Maintenance PrecautionsMAINTENANCE TABLE OF CONTENTSAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWAPPENDIX 2 INTERFACE EA2-1GLOSSARIES 1. PRODUCT OVERVIEW 1.2 Features 1.3 Unpacking 1.4 Accessories1.1 Introduction Safety consciousnessAs of August When purchasing the power cord1.5.1 Dimensions 1.5.2 Front View 1.5 Appearance1.5.3 Rear View Print Head Media Holder Media Holder Lock Switch Cover Open Sensor 1.5.4 InteriorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide PlatenPrinter status 1.5.5 Button and Indicator Lamp2.1 Precautions 2. PRINTER SETUP2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF2.3.1 Turning ON the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printerc d e f g 2.4 Connecting the Cables to the Printer2.5 Connecting the Power Adapter and the Power Cord 2.6 Opening/Closing the Top Cover To open the Top CoverTo close the Top Cover ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode Strip mode Option How to set the mediaCut mode Option How to Load Fanfold Paper Stock2. Insert the Media Shaft into the core of the media roll 2.8 Media Sensor Test, and Dump Mode different type Utilities2.8.1 Media Sensor Calibration The following commands should not affect the test print issue 2.8.2 Self Print Test and Dump ModePrint test label sample D, AX, XS, Z21, Z22 without AYE2-16 2.8.2 Self Print Test and Dump Mode Cont2.9 How to Use an SD Card „ Inserting an SD Card„ Removing an SD Card 3.1 Cleaning 3. MAINTENANCE3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.4 Media Housing 3.1.2 Platen/Sensors3.1.3 Cover Option 3.2 Care/Handling of the Media4.1 Troubleshooting Guide 4. TROUBLESHOOTINGSymptom Solutions4.2 Status Lamp ColorStatus 4.3 Removing Jammed Media APPENDIX 1 SPECIFICATIONS A1.1 PrinterB-EV4D-GS14-QM-R ENGLISH VERSION EO1-33088 A1.2 Options B-EV4D-TS14-QM-RA1.3 Media A1.2 OptionsA1.3.1 Media Type Option NameA1.3.1 Media Type Cont A1.3.2 Detection Area of the Transmissive SensorUnit mm inch A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaBlack Mark The figure below shows the effective print area on the media 5. Line weight should be 3 to 12 dotsAPPENDIX 2 INTERFACE Interface CablesRS-232C Cable description GLOSSARIES Supply A print head using thermal transfer or thermal direct printing methodThermal print head MediaPage Page EO1-33088