Toshiba B-EV4D SERIES, EO1-33088 owner manual Opening/Closing the Top Cover, To open the Top Cover

Page 17

2.6Opening/Closing the Top Cover

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.6 Opening/Closing the Top Cover

2.6Opening/Closing the Top Cover

WARNING!

To avoid injury, be careful not to trap your fingers while opening or closing the cover.

CAUTION!

1.Be careful not to touch the Print Head Element when opening the Top Cover.

Failure to do this may cause missing dots by static electricity or other print quality problems.

2.Do not cover the Cover Open Sensor with your finger, hand, etc. Doing so may cause the sensor to wrongly detect a cover close state.

When opening or closing the Top Cover, please be sure to follow the instructions below.

To open the Top Cover:

1.Press down the Top Cover Release Button to unlock the Top Cover, then fully open the Top Cover.

Top Cover

Top Cover

Release Button

As the Top Cover is held by the damper, it does not close under its own weight.

NOTE:

Be sure to close the Top Cover completely. Failure to do this may affect the print quality.

To close the Top Cover:

1.Press down the portions of the Top Cover indicated by the arrows until they click into position.

Top Cover

E2- 6

Image 17

Contents TOSHIBA Barcode Printer B-EV4D SERIESOwner’s Manual VORSICHT N258CE Compliance for EU only Safety Summary Safety SummaryMeanings of Each Symbol Request Regarding Maintenance PrecautionsMAINTENANCE TABLE OF CONTENTSAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWGLOSSARIES APPENDIX 2 INTERFACEEA2-1 1. PRODUCT OVERVIEW 1.2 Features 1.3 Unpacking 1.4 Accessories1.1 Introduction Safety consciousnessAs of August When purchasing the power cord1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance Print Head Media Holder Media Holder Lock Switch Cover Open Sensor 1.5.4 InteriorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide PlatenPrinter status 1.5.5 Button and Indicator Lamp2.1 Precautions 2. PRINTER SETUP2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printerc d e f g 2.4 Connecting the Cables to the Printer2.5 Connecting the Power Adapter and the Power Cord To close the Top Cover 2.6 Opening/Closing the Top CoverTo open the Top Cover ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode Strip mode Option How to set the mediaCut mode Option How to Load Fanfold Paper Stock2. Insert the Media Shaft into the core of the media roll 2.8.1 Media Sensor Calibration 2.8 Media SensorTest, and Dump Mode different type Utilities The following commands should not affect the test print issue 2.8.2 Self Print Test and Dump ModePrint test label sample D, AX, XS, Z21, Z22 without AYE2-16 2.8.2 Self Print Test and Dump Mode Cont„ Removing an SD Card 2.9 How to Use an SD Card„ Inserting an SD Card 3.1 Cleaning 3. MAINTENANCE3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.3 Cover 3.1.4 Media Housing3.1.2 Platen/Sensors Option 3.2 Care/Handling of the Media4.1 Troubleshooting Guide 4. TROUBLESHOOTINGSymptom SolutionsStatus 4.2 Status LampColor 4.3 Removing Jammed Media B-EV4D-GS14-QM-R APPENDIX 1 SPECIFICATIONSA1.1 Printer ENGLISH VERSION EO1-33088 A1.2 Options B-EV4D-TS14-QM-RA1.3 Media A1.2 OptionsA1.3.1 Media Type Option NameUnit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Black Mark A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area The figure below shows the effective print area on the media 5. Line weight should be 3 to 12 dotsRS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Supply A print head using thermal transfer or thermal direct printing methodThermal print head MediaPage Page EO1-33088