Toshiba B-EV4D SERIES, EO1-33088 owner manual Loading the Media Cont, Batch mode

Page 21

Batch mode:

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.7 Loading the Media

2.7Loading the Media (Cont.)

9.Close the Top Cover gently and push down the arrow-indicating portions until they click.

10.Press the [FEED] button to check for a proper media feed.

FEED Button

CAUTION!

To separate the printed media from the media roll in batch mode, be sure to tear off the media at the Media Outlet or cut the media past the Strip Plate. If you tear off the media at the Print Head by mistake, be sure to feed one label (10 mm or more) with the FEED Button prior to a next issue. Failure to do this may cause a paper jam.

There are three issue modes available for this printer.

Batch mode:

In the batch mode, the media is continuously printed and fed until the number of media specified in the issue command has been printed.

E2-10

Image 21

Contents B-EV4D SERIES Owner’s ManualTOSHIBA Barcode Printer N258 CE Compliance for EU onlyVORSICHT Safety Summary Meanings of Each SymbolSafety Summary Request Regarding Maintenance PrecautionsMAINTENANCE TABLE OF CONTENTSAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWAPPENDIX 2 INTERFACE EA2-1GLOSSARIES 1. PRODUCT OVERVIEW 1.2 Features 1.3 Unpacking 1.4 Accessories1.1 Introduction Safety consciousnessAs of August When purchasing the power cord1.5.1 Dimensions 1.5.2 Front View 1.5 Appearance1.5.3 Rear View Print Head Media Holder Media Holder Lock Switch Cover Open Sensor 1.5.4 InteriorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide PlatenPrinter status 1.5.5 Button and Indicator Lamp2.1 Precautions 2. PRINTER SETUP2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF2.3.1 Turning ON the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printerc d e f g 2.4 Connecting the Cables to the Printer2.5 Connecting the Power Adapter and the Power Cord 2.6 Opening/Closing the Top Cover To open the Top CoverTo close the Top Cover ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode Strip mode Option How to set the mediaCut mode Option How to Load Fanfold Paper Stock2. Insert the Media Shaft into the core of the media roll 2.8 Media Sensor Test, and Dump Mode different type Utilities2.8.1 Media Sensor Calibration The following commands should not affect the test print issue 2.8.2 Self Print Test and Dump ModePrint test label sample D, AX, XS, Z21, Z22 without AYE2-16 2.8.2 Self Print Test and Dump Mode Cont2.9 How to Use an SD Card „ Inserting an SD Card„ Removing an SD Card 3.1 Cleaning 3. MAINTENANCE3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.4 Media Housing 3.1.2 Platen/Sensors3.1.3 Cover Option 3.2 Care/Handling of the Media4.1 Troubleshooting Guide 4. TROUBLESHOOTINGSymptom Solutions4.2 Status Lamp ColorStatus 4.3 Removing Jammed Media APPENDIX 1 SPECIFICATIONS A1.1 PrinterB-EV4D-GS14-QM-R ENGLISH VERSION EO1-33088 A1.2 Options B-EV4D-TS14-QM-RA1.3 Media A1.2 OptionsA1.3.1 Media Type Option NameA1.3.1 Media Type Cont A1.3.2 Detection Area of the Transmissive SensorUnit mm inch A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaBlack Mark The figure below shows the effective print area on the media 5. Line weight should be 3 to 12 dotsAPPENDIX 2 INTERFACE Interface CablesRS-232C Cable description GLOSSARIES Supply A print head using thermal transfer or thermal direct printing methodThermal print head MediaPage Page EO1-33088