Toshiba EO1-33088 How to Use an SD Card, Inserting an SD Card, Removing an SD Card

Page 28

2.9How to Use an SD Card

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.9 How to Use an SD Card

2.9How to Use an SD Card

CAUTION!

1.Turn off the printer before inserting or removing an SD card. Failure to do this may destroy the data in the SD card.

2.Do not turn off the printer during access to the SD card, as doing so may destroy the data in the SD card.

3.For handling of the SD card, refer to the instruction supplied with the SD card.

This printer enables you to save print formats, writable characters, True Type fonts, etc. in commercially available SD cards.

For available SD card types, please ask the nearest TOSHIBA TEC representative.

For how to save data in an SD card, please refer to the External Equipment Interface Specification stored in the CD-ROM.

Inserting an SD Card

1.Turn off the printer and open the SD card slot cover.

2.Hold an SD card with the print surface facing up, and insert it into the SD card slot until it clicks.

SD Card Slot

Cover

SD Card

3.Close the SD card slot cover.

Removing an SD Card

1.Confirm no access is made to the SD card, and turn off the printer.

2.Open the SD card slot cover.

3.Push the SD card. The SD card pops up.

4.Remove it from the slot, and close the SD card slot cover.

E2-17

Image 28

Contents Owner’s Manual B-EV4D SERIESTOSHIBA Barcode Printer CE Compliance for EU only N258VORSICHT Meanings of Each Symbol Safety SummarySafety Summary Precautions Request Regarding MaintenanceTABLE OF CONTENTS MAINTENANCEAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWEA2-1 APPENDIX 2 INTERFACEGLOSSARIES 1.2 Features 1.3 Unpacking 1.4 Accessories 1. PRODUCT OVERVIEW1.1 Introduction Safety consciousnessWhen purchasing the power cord As of August1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View1.5.3 Rear View 1.5.4 Interior Print Head Media Holder Media Holder Lock Switch Cover Open SensorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3 Turning the Printer ON/OFF 2.2 Procedure before Operation2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll Test, and Dump Mode different type Utilities 2.8 Media Sensor2.8.1 Media Sensor Calibration 2.8.2 Self Print Test and Dump Mode The following commands should not affect the test print issuePrint test label sample D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-16„ Inserting an SD Card 2.9 How to Use an SD Card„ Removing an SD Card 3. MAINTENANCE 3.1 Cleaning3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.2 Platen/Sensors 3.1.4 Media Housing3.1.3 Cover 3.2 Care/Handling of the Media Option4. TROUBLESHOOTING 4.1 Troubleshooting GuideSymptom SolutionsColor 4.2 Status LampStatus 4.3 Removing Jammed Media A1.1 Printer APPENDIX 1 SPECIFICATIONSB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.2 Options A1.3 MediaA1.3.1 Media Type Option NameA1.3.2 Detection Area of the Transmissive Sensor A1.3.1 Media Type ContUnit mm inch A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaInterface Cables APPENDIX 2 INTERFACERS-232C Cable description GLOSSARIES A print head using thermal transfer or thermal direct printing method SupplyThermal print head MediaPage Page EO1-33088