Toshiba EO1-33088, B-EV4D SERIES owner manual Connecting the Power Adapter and the Power Cord

Page 16

2.5Connecting the Power Adapter and the Power Cord

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.5 Connecting the Power Adapter and the Power Cord

2.5Connecting the Power Adapter and the Power Cord

NOTES:

1.Since the power cord is not enclosed in this printer, please purchase a proper one after referring to page 1-2.

2.The EA10953 AC adapter should be exclusively used for the B-EV4D Series printer. The B-EV4D Series printer must be powered by the EA10953 AC adapter.

1.Make sure that the printer power switch is in the OFF (O) position.

2.Insert the Power Cord into the inlet of the Power Adapter.

Power Cord

Power Adapter

3.Insert the Power Adapter connector into the Power Jack on the rear of the printer.

Power Jack

Power Adapter

Connector

E2- 5

Image 16

Contents Owner’s Manual B-EV4D SERIESTOSHIBA Barcode Printer CE Compliance for EU only N258VORSICHT Meanings of Each Symbol Safety SummarySafety Summary Precautions Request Regarding MaintenanceTABLE OF CONTENTS MAINTENANCEAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWEA2-1 APPENDIX 2 INTERFACEGLOSSARIES 1.2 Features 1.3 Unpacking 1.4 Accessories 1. PRODUCT OVERVIEW1.1 Introduction Safety consciousnessWhen purchasing the power cord As of August1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View1.5.3 Rear View 1.5.4 Interior Print Head Media Holder Media Holder Lock Switch Cover Open SensorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3 Turning the Printer ON/OFF 2.2 Procedure before Operation2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll Test, and Dump Mode different type Utilities 2.8 Media Sensor2.8.1 Media Sensor Calibration 2.8.2 Self Print Test and Dump Mode The following commands should not affect the test print issuePrint test label sample D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-16„ Inserting an SD Card 2.9 How to Use an SD Card„ Removing an SD Card 3. MAINTENANCE 3.1 Cleaning3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.2 Platen/Sensors 3.1.4 Media Housing3.1.3 Cover 3.2 Care/Handling of the Media Option4. TROUBLESHOOTING 4.1 Troubleshooting GuideSymptom SolutionsColor 4.2 Status LampStatus 4.3 Removing Jammed Media A1.1 Printer APPENDIX 1 SPECIFICATIONSB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.2 Options A1.3 MediaA1.3.1 Media Type Option NameA1.3.2 Detection Area of the Transmissive Sensor A1.3.1 Media Type ContUnit mm inch A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaInterface Cables APPENDIX 2 INTERFACERS-232C Cable description GLOSSARIES A print head using thermal transfer or thermal direct printing method SupplyThermal print head MediaPage Page EO1-33088