Toshiba B-EV4D SERIES APPENDIX 2 INTERFACE, Interface Cables, RS-232C Cable description

Page 41

APPENDIX 2 INTERFACE

ENGLISH VERSION EO1-33088

APPENDIX 2 INTERFACE

Interface Cables

To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:

•Fully shielded and fitted with metal or metallized connector housings.

•Keep as short as possible.

•Should not be bundled tightly with power cords.

•Should not be tied to power line conduits.

RS-232C Cable description

The serial data cable used to connect the printer to a host computer should be one of the following two types (9-pin or 25-pin connector):

Connector to the Host Computer

Function	9 pin	25 pin

RXD	2	3
TXD	3	2
DTR	4	20
GND	5	7
DSR	6	6
RTS	7	4
CTS	8	5

Connector to Printer

Pin No.	Function
1	+5V
2	TXD
3	RXD
4	RTS
5	GND
6	CTS
7	RTS
8	CTS
9	+5V

NOTE:

Use an RS-232C cable with a connector with inch type securing screws.

EA2- 1

Image 41

Contents TOSHIBA Barcode Printer B-EV4D SERIESOwner’s Manual VORSICHT N258CE Compliance for EU only Safety Summary Safety SummaryMeanings of Each Symbol Request Regarding Maintenance PrecautionsMAINTENANCE TABLE OF CONTENTSAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWGLOSSARIES APPENDIX 2 INTERFACEEA2-1 1. PRODUCT OVERVIEW 1.2 Features 1.3 Unpacking 1.4 Accessories1.1 Introduction Safety consciousnessAs of August When purchasing the power cord1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance Print Head Media Holder Media Holder Lock Switch Cover Open Sensor 1.5.4 InteriorTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Media Guide PlatenPrinter status 1.5.5 Button and Indicator Lamp2.1 Precautions 2. PRINTER SETUP2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printerc d e f g 2.4 Connecting the Cables to the Printer2.5 Connecting the Power Adapter and the Power Cord To close the Top Cover 2.6 Opening/Closing the Top CoverTo open the Top Cover ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode Strip mode Option How to set the mediaCut mode Option How to Load Fanfold Paper Stock2. Insert the Media Shaft into the core of the media roll 2.8.1 Media Sensor Calibration 2.8 Media SensorTest, and Dump Mode different type Utilities The following commands should not affect the test print issue 2.8.2 Self Print Test and Dump ModePrint test label sample D, AX, XS, Z21, Z22 without AYE2-16 2.8.2 Self Print Test and Dump Mode Cont„ Removing an SD Card 2.9 How to Use an SD Card„ Inserting an SD Card 3.1 Cleaning 3. MAINTENANCE3.1.1 Print Head 4. Do not pour water directly onto the printer3.1.3 Cover 3.1.4 Media Housing3.1.2 Platen/Sensors Option 3.2 Care/Handling of the Media4.1 Troubleshooting Guide 4. TROUBLESHOOTINGSymptom SolutionsStatus 4.2 Status LampColor 4.3 Removing Jammed Media B-EV4D-GS14-QM-R APPENDIX 1 SPECIFICATIONSA1.1 Printer ENGLISH VERSION EO1-33088 A1.2 Options B-EV4D-TS14-QM-RA1.3 Media A1.2 OptionsA1.3.1 Media Type Option NameUnit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Black Mark A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area The figure below shows the effective print area on the media 5. Line weight should be 3 to 12 dotsRS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Supply A print head using thermal transfer or thermal direct printing methodThermal print head MediaPage Page EO1-33088