Toshiba EO1-33088, B-EV4D SERIES owner manual APPENDIX 2 INTERFACE, EA2-1, Glossaries

Page 6

APPENDIX 2 INTERFACE

ENGLISH VERSION EO1-33088

APPENDIX 2 INTERFACE

EA2-1

GLOSSARIES

CAUTION!

1.This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC.

2.The contents of this manual may be changed without notification.

3.Please refer to your local Authorized Service representative with regard to any queries you may have in this manual.

Image 6

Contents B-EV4D SERIES Owner’s ManualTOSHIBA Barcode Printer N258 CE Compliance for EU onlyVORSICHT Safety Summary Meanings of Each SymbolSafety Summary Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWAPPENDIX 2 INTERFACE EA2-1GLOSSARIES 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessWhen purchasing the power cord As of August1.5.1 Dimensions 1.5.2 Front View 1.5 Appearance1.5.3 Rear View Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord 2.6 Opening/Closing the Top Cover To open the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll 2.8 Media Sensor Test, and Dump Mode different type Utilities2.8.1 Media Sensor Calibration Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-162.9 How to Use an SD Card „ Inserting an SD Card„ Removing an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.4 Media Housing 3.1.2 Platen/Sensors3.1.3 Cover 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide Solutions4.2 Status Lamp ColorStatus 4.3 Removing Jammed Media APPENDIX 1 SPECIFICATIONS A1.1 PrinterB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameA1.3.1 Media Type Cont A1.3.2 Detection Area of the Transmissive SensorUnit mm inch A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaAPPENDIX 2 INTERFACE Interface CablesRS-232C Cable description GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088