Dell GX1 Parallel Port Connector, Mouse Connector, USB Connectors, Integrated NIC Connector

Page 10

Introduction: Dell OptiPlex GX1 Low-Profile Managed PC Systems

Parallel Port Connector

The integrated parallel port uses a 25-pin D-subminiature connector on the computer's back panel.

This I/O port sends data in parallel format (where 8 data bits, or 1 byte, are sent simultaneously over eight separate lines in a single cable). The parallel port is used primarily for printers.

The default designation of your computer's integrated parallel port is LPT1. Port designations are used, for example, in software installation procedures to identify the port to which your printer is attached, thus telling your software where to send its output. (An incorrect designation prevents the printer from printing or causes scrambled print.)

NOTE: The integrated parallel port is automatically disabled if the system detects an installed expansion card containing a parallel port configured to the same address as specified in the Parallel Port option in the System Setup Program.

Mouse Connector

Your system uses a PS/2-compatible mouse. The mouse cable attaches to a 6-pin miniature Deutsche Inductive Norm (DIN) connector on the back panel of your computer. Turn off the computer and any attached peripherals before connecting a mouse to the computer.

A PS/2-compatible mouse works as does an industry-standard serial mouse or bus mouse except that it has its own dedicated connector, which frees up the serial ports and does not require an expansion card. Mouse driver software gives the mouse priority with the microprocessor by issuing interrupt request (IRQ) 12 whenever a new mouse movement is made. The drivers also pass along the mouse data to the application that is in control.

USB Connectors

Your system contains two USB connectors for attaching USB-compliant devices. USB-compliant devices are typically peripherals such as keyboards, mice, printers, and computer speakers.

If you reconfigure your hardware, you may need pin number and signal information for the USB connectors.

Integrated NIC Connector

Your system has an integrated 10/100-Mbps 3Com PCI 3C905B-TX Ethernet NIC. The NIC provides all the functions of a separate network expansion card and supports both the 10BASE-T and 100BASE-TX Ethernet standards.

The NIC includes a Wakeup On LAN feature that enables the computer to be started by a special local area network (LAN) signal from a server management console. Wakeup On LAN provides remote computer setup, software downloading and installation, file updates, and asset tracking after hours and on weekends when LAN traffic is typically at a minimum.

The NIC connector on the computer's back panel has the following indicators:

A yellow activity indicator flashes when the system is transmitting or receiving network data. (A high volume of network traffic may make this indicator appear to be in a steady "on" state.)

file:///C/infodev/2013/eDoc/OpGX1/SQRG/introduc.htm[2/21/2013 11:52:57 AM]

Image 10
Contents Initial release 7 Dec Last revised 31 Jan System Features OverviewHardware Features 640 × True-color 32 bpp 85 Hz 800 ×Software Features Manageability Features Dell OpenManage ProgramFault Management Auto Power On Wakeup On LANTemperature Monitoring Security FeaturesConnecting Peripheral Devices O Ports, Connectors, and IndicatorsUSB Connectors Parallel Port ConnectorMouse Connector Integrated NIC ConnectorSerial Port Connectors Audio ConnectorsVideo Connector Keyboard ConnectorUsing the Power Switch Using the Optional Stand for Vertical Orientation Attaching the Optional Stand for Vertical OrientationEnergy Star Compliance Energy Star EmblemAccessing Online Documentation Getting HelpEntering the System Setup Program Enter the System Setup program as followsSystem Setup Screens System Setup ScreensPage System-Setup Navigation Keys Keys Action Using the System Setup ProgramSystem Setup Options TimeDiskette Drive A, Diskette Drive B, and Use ZIP as a or B DateDrives Primary and Secondary Reserved Memory Chassis Intrusion CPU SpeedNum Lock DAC SnoopSystem Password Keyboard ErrorsPassword Status Boot Sequence Device-List Screen Navigation Keys Keys ActionSample Device List Screen Setup Password Saving Monitor Power Power ManagementSaving Eide Hard-Disk Drive Power Sound MouseParallel Port Parallel ModeSerial Port 1 and Serial Port IDE Hard DiskSpeaker Using the System Password FeatureDiskette System Data OptionsAssigning a System Password Using Your System Password to Secure Your System Type the password and press EnterUsing the Setup Password Feature Deleting or Changing an Existing System PasswordAssigning a Setup Password Page Responding to Error Messages Back to ContentsOverview Quick Start About the ICUPreparing to Use the ICU When to Run the ICUICU Database Starting the ICU Accessing HelpBacking Up the ICU Diskette Making Selections in the ICU Adding a Listed CardICU Keys Keys Action Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card Viewing Resources System Resource Usage Dialog BoxLocking and Unlocking Cards Saving the System ConfigurationExiting From the ICU Locking and Unlocking All ResourcesLocking and Unlocking Configuration Resources Safety First For You and Your Computer Before You BeginRemoving the Computer Cover Unpacking Your Hardware OptionReplacing the Computer Cover Replacing the Computer CoverInside Your Computer Computer Orientation ViewJumpers System Board JumpersSystem-Board Jumper Settings Description BUS66MSystem Board and Riser Board Labels LPT1Removing and Replacing the Expansion-Card Cage Removing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Cards Expansion SlotsRemoving the Filler Bracket Removing an Expansion Card Adding Memory DIMMs and Dimm SocketsPerforming a Memory Upgrade Installing a Dimm Installing a Dimm Removing a Dimm Adding Video MemoryInstalling a Video-Memory Upgrade Module Upgrading the Microprocessor Removing the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing and Replacing Front-Panel Inserts Removing the Front-Panel Insert for a 5.25-Inch BayConnecting Drives DC Power Cable ConnectorInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Installing an Eide Hard-Disk Drive Eide Drive AddressingRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Installing Scsi Devices Scsi Configuration GuidelinesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives System Information MicroprocessorExpansion Bus Drives MemoryPorts Video Key CombinationsPhysical Controls and IndicatorsPower EnvironmentalBack to Contents ICU Error Messages Message Probable Cause Corrective ActionLoaded card is not a Conflictingcard This is An Eisa system. Use Message Configuration Manager MessagesProbable Cause Corrective Action Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions
Related manuals
Manual 12 pages 4.6 Kb