Dell GX1 technical specifications Drive Locations

Page 74

Installing Drives: Dell OptiPlex GX1 Low-Profile Managed PC Systems

Back to Contents Page

Installing Drives: Dell™ OptiPlex™ GX1 Low-Profile Managed PC Systems

Overview

Installing a Drive in the 5.25-Inch Drive Bay

Removing and Replacing Front-Panel Inserts

Installing an EIDE Hard-Disk Drive

Connecting Drives

Installing SCSI Devices

Overview

Your Dell computer has three drive bays for installing the following types of drives (see Figure 1)

The externally accessible drive bays at the front of the computer consist of one 3.5-inch drive bay (dedicated to a 3.5-inch diskette drive) and one 5.25-inch bay that can hold one half-height, 5.25-inch device—typically a tape drive or CD-ROM drive. Alternately, a 3.5-inch device can be installed in the 5.25-inch bay using adapters available from Dell.

The hard-disk drive bay (located to the left of the externally accessible drive bays) can hold a 3.5-inch enhanced integrated drive electronics (EIDE) or small computer system interface (SCSI) hard-disk drive.

The next two subsections contain information that you will need in several of the installation procedures described later in this section. The remaining subsections cover each type of drive installation.

NOTE: In all of the following procedures, left and right refer to your left and right as you face the front of the computer.

Figure 1. Drive Locations

file:///C/infodev/2013/eDoc/OpGX1/SQRG/drives.htm[2/21/2013 11:53:04 AM]

Image 74
Contents Initial release 7 Dec Last revised 31 Jan System Features OverviewHardware Features 640 × True-color 32 bpp 85 Hz 800 ×Software Features Manageability Features Dell OpenManage ProgramFault Management Auto Power On Wakeup On LANTemperature Monitoring Security FeaturesConnecting Peripheral Devices O Ports, Connectors, and IndicatorsUSB Connectors Parallel Port ConnectorMouse Connector Integrated NIC ConnectorSerial Port Connectors Audio ConnectorsVideo Connector Keyboard ConnectorUsing the Power Switch Using the Optional Stand for Vertical Orientation Attaching the Optional Stand for Vertical OrientationEnergy Star Compliance Energy Star EmblemAccessing Online Documentation Getting HelpEntering the System Setup Program Enter the System Setup program as followsSystem Setup Screens System Setup ScreensPage System-Setup Navigation Keys Keys Action Using the System Setup ProgramSystem Setup Options TimeDrives Primary and Secondary DateDiskette Drive A, Diskette Drive B, and Use ZIP as a or B Reserved Memory Chassis Intrusion CPU SpeedNum Lock DAC SnoopPassword Status Keyboard ErrorsSystem Password Boot Sequence Device-List Screen Navigation Keys Keys ActionSample Device List Screen Setup Password Saving Eide Hard-Disk Drive Power Power ManagementSaving Monitor Power Sound MouseParallel Port Parallel ModeSerial Port 1 and Serial Port IDE Hard DiskSpeaker Using the System Password FeatureDiskette System Data OptionsAssigning a System Password Using Your System Password to Secure Your System Type the password and press EnterUsing the Setup Password Feature Deleting or Changing an Existing System PasswordAssigning a Setup Password Page Responding to Error Messages Back to ContentsOverview Quick Start About the ICUICU Database When to Run the ICUPreparing to Use the ICU Backing Up the ICU Diskette Accessing HelpStarting the ICU ICU Keys Keys Action Adding a Listed CardMaking Selections in the ICU Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card Viewing Resources System Resource Usage Dialog BoxLocking and Unlocking Cards Saving the System ConfigurationExiting From the ICU Locking and Unlocking All ResourcesLocking and Unlocking Configuration Resources Safety First For You and Your Computer Before You BeginRemoving the Computer Cover Unpacking Your Hardware OptionReplacing the Computer Cover Replacing the Computer CoverInside Your Computer Computer Orientation ViewJumpers System Board JumpersSystem-Board Jumper Settings Description BUS66MSystem Board and Riser Board Labels LPT1Removing and Replacing the Expansion-Card Cage Removing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Cards Expansion SlotsRemoving the Filler Bracket Removing an Expansion Card Adding Memory DIMMs and Dimm SocketsPerforming a Memory Upgrade Installing a Dimm Installing a Dimm Removing a Dimm Adding Video MemoryInstalling a Video-Memory Upgrade Module Upgrading the Microprocessor Removing the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing and Replacing Front-Panel Inserts Removing the Front-Panel Insert for a 5.25-Inch BayConnecting Drives DC Power Cable ConnectorInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Installing an Eide Hard-Disk Drive Eide Drive AddressingRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Installing Scsi Devices Scsi Configuration GuidelinesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Expansion Bus MicroprocessorSystem Information Ports MemoryDrives Video Key CombinationsPhysical Controls and IndicatorsPower EnvironmentalBack to Contents ICU Error Messages Message Probable Cause Corrective ActionLoaded card is not a Conflictingcard This is An Eisa system. Use Probable Cause Corrective Action Configuration Manager MessagesMessage Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions
Related manuals
Manual 12 pages 4.6 Kb