Dell GX1 technical specifications Securing the Hard-Disk Drive to the Bracket

Page 83

Installing Drives: Dell OptiPlex GX1 Low-Profile Managed PC Systems

6.Secure the drive bracket to the new drive.

Turn the drive upside down, and locate the four screw holes around its perimeter.

Orient the drive bracket so that the end labeled "CONNECTOR" faces the side of the drive containing the interface and power connectors. Place the bracket on the drive, and secure it with four screws (see Figure 12).

Figure 12. Securing the Hard-Disk Drive to the Bracket

7.Reinstall the hard-disk drive/bracket assembly in the chassis.

Grasp the bracket by the tab containing the captive screw, and hold the bracket at a 45-degree angle to the chassis floor. Align the two tabs on the other side of the bracket with the score marks on the chassis floor. Insert the two tabs into the slots in the chassis floor divider, and rotate the assembly downward. Then tighten the captive screw until the bracket is securely fastened to the chassis floor (see Figure 11).

NOTICE: You must match the colored strip on the EIDE cable with pin 1 on the drive's interface connector to avoid possible damage to your system.

8.Connect one end of the EIDE cable to the 40-pin interface connector on the back of the hard-disk drive (see Figure 13).

The cable is keyed so that the colored edge of the EIDE cable lines up with the pin-1 end of the interface connector.

Figure 13. Attaching Hard-Disk Drive Cables

file:///C/infodev/2013/eDoc/OpGX1/SQRG/drives.htm[2/21/2013 11:53:04 AM]

Image 83

Contents Initial release 7 Dec Last revised 31 Jan Overview System Features640 × True-color 32 bpp 85 Hz 800 × Hardware FeaturesSoftware Features Dell OpenManage Program Manageability FeaturesFault Management Wakeup On LAN Auto Power OnSecurity Features Temperature MonitoringO Ports, Connectors, and Indicators Connecting Peripheral DevicesIntegrated NIC Connector Parallel Port ConnectorMouse Connector USB ConnectorsKeyboard Connector Audio ConnectorsVideo Connector Serial Port ConnectorsUsing the Power Switch Attaching the Optional Stand for Vertical Orientation Using the Optional Stand for Vertical OrientationEnergy Star Emblem Energy Star ComplianceGetting Help Accessing Online DocumentationEnter the System Setup program as follows Entering the System Setup ProgramSystem Setup Screens System Setup ScreensPage Time Using the System Setup ProgramSystem Setup Options System-Setup Navigation Keys Keys ActionDrives Primary and Secondary DateDiskette Drive A, Diskette Drive B, and Use ZIP as a or B Reserved Memory DAC Snoop CPU SpeedNum Lock Chassis IntrusionPassword Status Keyboard ErrorsSystem Password Device-List Screen Navigation Keys Keys Action Boot SequenceSample Device List Screen Setup Password Saving Eide Hard-Disk Drive Power Power ManagementSaving Monitor Power Mouse SoundIDE Hard Disk Parallel ModeSerial Port 1 and Serial Port Parallel PortSystem Data Options Using the System Password FeatureDiskette SpeakerAssigning a System Password Type the password and press Enter Using Your System Password to Secure Your SystemDeleting or Changing an Existing System Password Using the Setup Password FeatureAssigning a Setup Password Page Back to Contents Responding to Error MessagesOverview About the ICU Quick StartICU Database When to Run the ICUPreparing to Use the ICU Backing Up the ICU Diskette Accessing HelpStarting the ICU ICU Keys Keys Action Adding a Listed CardMaking Selections in the ICU Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card System Resource Usage Dialog Box Viewing ResourcesLocking and Unlocking All Resources Saving the System ConfigurationExiting From the ICU Locking and Unlocking CardsLocking and Unlocking Configuration Resources Before You Begin Safety First For You and Your ComputerUnpacking Your Hardware Option Removing the Computer CoverReplacing the Computer Cover Replacing the Computer CoverComputer Orientation View Inside Your ComputerSystem Board Jumpers JumpersBUS66M System-Board Jumper Settings DescriptionLPT1 System Board and Riser Board LabelsRemoving the Expansion-Card Cage Removing and Replacing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Slots Expansion CardsRemoving the Filler Bracket Removing an Expansion Card DIMMs and Dimm Sockets Adding MemoryPerforming a Memory Upgrade Installing a Dimm Adding Video Memory Installing a Dimm Removing a DimmInstalling a Video-Memory Upgrade Module Removing the Microprocessor Upgrading the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing the Front-Panel Insert for a 5.25-Inch Bay Removing and Replacing Front-Panel InsertsDC Power Cable Connector Connecting DrivesInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Eide Drive Addressing Installing an Eide Hard-Disk DriveRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Scsi Configuration Guidelines Installing Scsi DevicesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Expansion Bus MicroprocessorSystem Information Ports MemoryDrives Key Combinations VideoEnvironmental Controls and IndicatorsPower PhysicalBack to Contents Message Probable Cause Corrective Action ICU Error MessagesLoaded card is not a Conflictingcard This is An Eisa system. Use Probable Cause Corrective Action Configuration Manager MessagesMessage Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions

Related manuals

Manual 12 pages 4.6 Kb