Dell GX1 technical specifications Removing a Card

Page 48

Using the ISA Configuration Utility: Dell OptiPlex GX1 Low-Profile Managed PC Systems

indicated in the card's documentation), select one of the available values offered by the utility and click OK.

If you are providing values for the I/O port or memory resource, you must enter the starting and ending addresses in hexadecimal format using the two fields provided by the Specify Memory or Specify I/O Port dialog box.

6.When you have finished selecting resources for the unlisted card, click OK in the Configure Unlisted Card dialog box.

A message box appears, notifying you either that the card is using its default settings or that it cannot use its default settings and must be reconfigured.

7.Click OK. If the card must be reconfigured, record the resource settings recommended by the ICU. Click Close to accept the resource settings currently displayed.

8.If you had to assign a disallowed resource value to the card in steps 5, 6, and 7, click each of the other cards, and then click View until you find another card using a resource value that is allowed for the unlisted card. Reassign the resource setting for this other card. Then modify the resource settings for the unlisted card so that it uses an allowable value.

NOTE: After modifying the system configuration, you must turn off the system to install, remove, or change jumper settings on the non-Plug and Play ISA expansion cards to match the settings you selected in the ICU.

Removing a Card

Before you remove a non-Plug and Play ISA expansion card from your computer, you must use the ICU to remove the card from the system configuration.

NOTE: When you remove a Plug and Play or PCI expansion card from your computer, you do not need to run the ICU. To remove a Plug and Play or PCI expansion card, complete steps 2 through 9 in "Removing an Expansion Card."

Use the following procedure to remove a non-Plug and Play ISA expansion card from your computer:

1.Start the ICU as described in "Starting the ICU."

2.Select the card from the current system configuration list in the ICU window.

3.Select Remove Card from the Configuration menu, or click Remove. The ICU requests verification that you want to remove the card.

4.Click Yes to free the resources allocated to the card and remove the card name from the list of active cards, or click No to cancel the operation.

The ICU returns to the ICU window.

NOTICE: After removing a card from the system configuration using the ICU, you must turn off

file:///C/infodev/2013/eDoc/OpGX1/SQRG/utility.htm[2/21/2013 11:53:00 AM]

Image 48
Contents Initial release 7 Dec Last revised 31 Jan System Features OverviewHardware Features 640 × True-color 32 bpp 85 Hz 800 ×Software Features Manageability Features Dell OpenManage ProgramFault Management Auto Power On Wakeup On LANTemperature Monitoring Security FeaturesConnecting Peripheral Devices O Ports, Connectors, and IndicatorsParallel Port Connector Mouse ConnectorUSB Connectors Integrated NIC ConnectorAudio Connectors Video ConnectorSerial Port Connectors Keyboard ConnectorUsing the Power Switch Using the Optional Stand for Vertical Orientation Attaching the Optional Stand for Vertical OrientationEnergy Star Compliance Energy Star EmblemAccessing Online Documentation Getting HelpEntering the System Setup Program Enter the System Setup program as followsSystem Setup Screens System Setup ScreensPage Using the System Setup Program System Setup OptionsSystem-Setup Navigation Keys Keys Action TimeDate Diskette Drive A, Diskette Drive B, and Use ZIP as a or BDrives Primary and Secondary Reserved Memory CPU Speed Num LockChassis Intrusion DAC SnoopKeyboard Errors System PasswordPassword Status Boot Sequence Device-List Screen Navigation Keys Keys ActionSample Device List Screen Setup Password Power Management Saving Monitor PowerSaving Eide Hard-Disk Drive Power Sound MouseParallel Mode Serial Port 1 and Serial PortParallel Port IDE Hard DiskUsing the System Password Feature DisketteSpeaker System Data OptionsAssigning a System Password Using Your System Password to Secure Your System Type the password and press EnterUsing the Setup Password Feature Deleting or Changing an Existing System PasswordAssigning a Setup Password Page Responding to Error Messages Back to ContentsOverview Quick Start About the ICUWhen to Run the ICU Preparing to Use the ICUICU Database Accessing Help Starting the ICUBacking Up the ICU Diskette Adding a Listed Card Making Selections in the ICUICU Keys Keys Action Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card Viewing Resources System Resource Usage Dialog BoxSaving the System Configuration Exiting From the ICULocking and Unlocking Cards Locking and Unlocking All ResourcesLocking and Unlocking Configuration Resources Safety First For You and Your Computer Before You BeginRemoving the Computer Cover Unpacking Your Hardware OptionReplacing the Computer Cover Replacing the Computer CoverInside Your Computer Computer Orientation ViewJumpers System Board JumpersSystem-Board Jumper Settings Description BUS66MSystem Board and Riser Board Labels LPT1Removing and Replacing the Expansion-Card Cage Removing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Cards Expansion SlotsRemoving the Filler Bracket Removing an Expansion Card Adding Memory DIMMs and Dimm SocketsPerforming a Memory Upgrade Installing a Dimm Installing a Dimm Removing a Dimm Adding Video MemoryInstalling a Video-Memory Upgrade Module Upgrading the Microprocessor Removing the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing and Replacing Front-Panel Inserts Removing the Front-Panel Insert for a 5.25-Inch BayConnecting Drives DC Power Cable ConnectorInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Installing an Eide Hard-Disk Drive Eide Drive AddressingRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Installing Scsi Devices Scsi Configuration GuidelinesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Microprocessor System InformationExpansion Bus Memory DrivesPorts Video Key CombinationsControls and Indicators PowerPhysical EnvironmentalBack to Contents ICU Error Messages Message Probable Cause Corrective ActionLoaded card is not a Conflictingcard This is An Eisa system. Use Configuration Manager Messages MessageProbable Cause Corrective Action Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions
Related manuals
Manual 12 pages 4.6 Kb