Dell GX1 technical specifications Energy Star Compliance, Energy Star Emblem

Page 14

Introduction: Dell OptiPlex GX1 Low-Profile Managed PC Systems

As you lower the stand into place, make sure that the locator pin (see Figure 4) fits into the corner hole of the hole pattern as shown. When the stand is in place, tighten the thumbscrew.

3. Rotate the computer so that the stand is at the bottom and the drives are at the top.

To remove the stand, turn the computer over so the stand is at the top, loosen the screw, lift the stand away, and place the computer in a horizontal position.

ENERGY STAR® Compliance

Certain configurations of Dell computer systems comply with the requirements set forth by the Environmental Protection Agency (EPA) for energy-efficient computers. If the front panel of your computer bears the ENERGY STAR® Emblem (see Figure 5), your original configuration complied with these requirements and all ENERGY STAR® power management features of the computer are enabled. To disable or change the operation of these features, you must change the setting for the Power Management option in the System Setup program. For instructions, see "Using the System Setup Program."

NOTES: As an ENERGY STAR® Partner, Dell Computer Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Any Dell computer bearing the ENERGY STAR® Emblem is certified to comply with EPA ENERGY STAR® requirements as configured when shipped by Dell. Any changes you make to this configuration (such as installing additional expansion cards or drives) may increase the system's power consumption beyond the limits set by the EPA's ENERGY STAR® Computers program.

Figure 5. ENERGY STAR® Emblem

The EPA's ENERGY STAR® Computers program is a joint effort between the EPA and computer manufacturers to reduce air pollution by promoting energy-efficient computer products. The EPA estimates that use of ENERGY STAR® computer products can save computer users up to two billion dollars annually in electricity costs. In turn, this reduction in electricity usage can reduce emissions of carbon dioxide, the gas

file:///C/infodev/2013/eDoc/OpGX1/SQRG/introduc.htm[2/21/2013 11:52:57 AM]

Image 14
Contents Initial release 7 Dec Last revised 31 Jan System Features OverviewHardware Features 640 × True-color 32 bpp 85 Hz 800 ×Software Features Manageability Features Dell OpenManage ProgramFault Management Auto Power On Wakeup On LANTemperature Monitoring Security FeaturesConnecting Peripheral Devices O Ports, Connectors, and IndicatorsUSB Connectors Parallel Port ConnectorMouse Connector Integrated NIC ConnectorSerial Port Connectors Audio ConnectorsVideo Connector Keyboard ConnectorUsing the Power Switch Using the Optional Stand for Vertical Orientation Attaching the Optional Stand for Vertical OrientationEnergy Star Compliance Energy Star EmblemAccessing Online Documentation Getting HelpEntering the System Setup Program Enter the System Setup program as followsSystem Setup Screens System Setup ScreensPage System-Setup Navigation Keys Keys Action Using the System Setup ProgramSystem Setup Options TimeDrives Primary and Secondary DateDiskette Drive A, Diskette Drive B, and Use ZIP as a or B Reserved Memory Chassis Intrusion CPU SpeedNum Lock DAC SnoopPassword Status Keyboard ErrorsSystem Password Boot Sequence Device-List Screen Navigation Keys Keys ActionSample Device List Screen Setup Password Saving Eide Hard-Disk Drive Power Power ManagementSaving Monitor Power Sound MouseParallel Port Parallel ModeSerial Port 1 and Serial Port IDE Hard DiskSpeaker Using the System Password FeatureDiskette System Data OptionsAssigning a System Password Using Your System Password to Secure Your System Type the password and press EnterUsing the Setup Password Feature Deleting or Changing an Existing System PasswordAssigning a Setup Password Page Responding to Error Messages Back to ContentsOverview Quick Start About the ICUICU Database When to Run the ICUPreparing to Use the ICU Backing Up the ICU Diskette Accessing HelpStarting the ICU ICU Keys Keys Action Adding a Listed CardMaking Selections in the ICU Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card Viewing Resources System Resource Usage Dialog BoxLocking and Unlocking Cards Saving the System ConfigurationExiting From the ICU Locking and Unlocking All ResourcesLocking and Unlocking Configuration Resources Safety First For You and Your Computer Before You BeginRemoving the Computer Cover Unpacking Your Hardware OptionReplacing the Computer Cover Replacing the Computer CoverInside Your Computer Computer Orientation ViewJumpers System Board JumpersSystem-Board Jumper Settings Description BUS66MSystem Board and Riser Board Labels LPT1Removing and Replacing the Expansion-Card Cage Removing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Cards Expansion SlotsRemoving the Filler Bracket Removing an Expansion Card Adding Memory DIMMs and Dimm SocketsPerforming a Memory Upgrade Installing a Dimm Installing a Dimm Removing a Dimm Adding Video MemoryInstalling a Video-Memory Upgrade Module Upgrading the Microprocessor Removing the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing and Replacing Front-Panel Inserts Removing the Front-Panel Insert for a 5.25-Inch BayConnecting Drives DC Power Cable ConnectorInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Installing an Eide Hard-Disk Drive Eide Drive AddressingRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Installing Scsi Devices Scsi Configuration GuidelinesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Expansion Bus MicroprocessorSystem Information Ports MemoryDrives Video Key CombinationsPhysical Controls and IndicatorsPower EnvironmentalBack to Contents ICU Error Messages Message Probable Cause Corrective ActionLoaded card is not a Conflictingcard This is An Eisa system. Use Probable Cause Corrective Action Configuration Manager MessagesMessage Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions
Related manuals
Manual 12 pages 4.6 Kb