Dell GX1 technical specifications

Page 72

Installing System Board Options: Dell OptiPlex GX1 Low-Profile Managed PC Systems

Time-of-day not set - please run SETUP program

or

Invalid configuration information - please run SETUP program

or

Strike the F1 key to continue, F2 to run the setup utility

To determine whether the battery needs replacing, reenter the time and date through the System Setup program (not through the MS-DOS® time and date commands) and exit the program properly to save the information (see "Using the System Setup Program" for instructions). Turn off your system and disconnect it from AC power for a few hours; then reconnect and turn on your system. Enter the System Setup program. If the date and time are not correct in the System Setup program, replace your battery.

You can operate your system without a battery; however, without a battery, the system configuration information is erased if the system is turned off or unplugged from AC power. In this case, you must enter the System Setup program and reset the configuration options.

CAUTION: There is a danger of the new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

CAUTION: Before you remove the computer cover, see "Safety First — For You and Your Computer."

Use the following procedure to replace the system battery with another CR2032 coin-cell battery:

1.If you have not already done so, make a copy of your system configuration information in the System Setup program.

If the settings are lost while you are replacing the battery, refer to your written or printed copy of the system configuration information to restore the correct settings. See "Using the System Setup Program" for instructions.

2.Remove the computer cover according to the instructions in "Removing the Computer Cover."

3.To access the battery on the system board, remove the expansion-card cage as described in "Removing the Expansion-Card Cage."

NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Make certain that the object is inserted between the battery and the socket before attempting to pry out the battery. Otherwise, you may damage the system board by prying off the socket or by breaking circuit traces on the system board.

4.Locate the battery and remove it.

The battery (see Figure 1) is mounted in a socket labeled "BATTERY," in the front-right corner of the system board (as you face the front of the system).

Pry the battery out of its socket with your fingers or with a blunt, nonconductive object, such as a plastic

file:///C/infodev/2013/eDoc/OpGX1/SQRG/options.htm[2/21/2013 11:53:02 AM]

Image 72
Contents Initial release 7 Dec Last revised 31 Jan System Features OverviewHardware Features 640 × True-color 32 bpp 85 Hz 800 ×Software Features Manageability Features Dell OpenManage ProgramFault Management Auto Power On Wakeup On LANTemperature Monitoring Security FeaturesConnecting Peripheral Devices O Ports, Connectors, and IndicatorsParallel Port Connector Mouse ConnectorUSB Connectors Integrated NIC ConnectorAudio Connectors Video ConnectorSerial Port Connectors Keyboard ConnectorUsing the Power Switch Using the Optional Stand for Vertical Orientation Attaching the Optional Stand for Vertical OrientationEnergy Star Compliance Energy Star EmblemAccessing Online Documentation Getting HelpEntering the System Setup Program Enter the System Setup program as followsSystem Setup Screens System Setup ScreensPage Using the System Setup Program System Setup OptionsSystem-Setup Navigation Keys Keys Action TimeDate Diskette Drive A, Diskette Drive B, and Use ZIP as a or BDrives Primary and Secondary Reserved Memory CPU Speed Num LockChassis Intrusion DAC SnoopKeyboard Errors System PasswordPassword Status Boot Sequence Device-List Screen Navigation Keys Keys ActionSample Device List Screen Setup Password Power Management Saving Monitor PowerSaving Eide Hard-Disk Drive Power Sound MouseParallel Mode Serial Port 1 and Serial PortParallel Port IDE Hard DiskUsing the System Password Feature DisketteSpeaker System Data OptionsAssigning a System Password Using Your System Password to Secure Your System Type the password and press EnterUsing the Setup Password Feature Deleting or Changing an Existing System PasswordAssigning a Setup Password Page Responding to Error Messages Back to ContentsOverview Quick Start About the ICUWhen to Run the ICU Preparing to Use the ICUICU Database Accessing Help Starting the ICUBacking Up the ICU Diskette Adding a Listed Card Making Selections in the ICUICU Keys Keys Action Add Network Card Dialog Box Configuration Settings Dialog Box for Assigning an IRQ Line Adding an Unlisted Card Specify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a Card Removing a Card Viewing Resources System Resource Usage Dialog BoxSaving the System Configuration Exiting From the ICULocking and Unlocking Cards Locking and Unlocking All ResourcesLocking and Unlocking Configuration Resources Safety First For You and Your Computer Before You BeginRemoving the Computer Cover Unpacking Your Hardware OptionReplacing the Computer Cover Replacing the Computer CoverInside Your Computer Computer Orientation ViewJumpers System Board JumpersSystem-Board Jumper Settings Description BUS66MSystem Board and Riser Board Labels LPT1Removing and Replacing the Expansion-Card Cage Removing the Expansion-Card CageReplacing the Expansion-Card Cage System Board Features Expansion Cards Expansion Cards Expansion SlotsRemoving the Filler Bracket Removing an Expansion Card Adding Memory DIMMs and Dimm SocketsPerforming a Memory Upgrade Installing a Dimm Installing a Dimm Removing a Dimm Adding Video MemoryInstalling a Video-Memory Upgrade Module Upgrading the Microprocessor Removing the MicroprocessorReplacing the System Battery Page System Battery and Battery Socket Drive Locations Removing and Replacing Front-Panel Inserts Removing the Front-Panel Insert for a 5.25-Inch BayConnecting Drives DC Power Cable ConnectorInstalling a Drive in the 5.25-Inch Drive Bay Removing the 3.5-Inch Diskette Drive/Bracket Assembly Installing the 5.25-Inch Diskette Drive Bracket Attaching Cables to a Drive in the 5.25-Inch Drive Bay Installing an Eide Hard-Disk Drive Eide Drive AddressingRemoving the Hard-Disk Drive Bracket Securing the Hard-Disk Drive to the Bracket ALERT! Cover was previously removed Page Installing Scsi Devices Scsi Configuration GuidelinesGeneral Procedure for Installing Scsi Devices Page ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Microprocessor System InformationExpansion Bus Memory DrivesPorts Video Key CombinationsControls and Indicators PowerPhysical EnvironmentalBack to Contents ICU Error Messages Message Probable Cause Corrective ActionLoaded card is not a Conflictingcard This is An Eisa system. Use Configuration Manager Messages MessageProbable Cause Corrective Action Error Failed to activate device, CSN=Card Select Number See Modifying a Card for instructions See Adding a Listed Card for instructions
Related manuals
Manual 12 pages 4.6 Kb