Dell W07B owner manual OptionDescription

Page 46

OptionDescription

NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled.

Deep Sleep Control

Fan Control Override

USB Wake Support

Wake on LAN / WLAN

Block Sleep

Allows you to define the controls when Deep Sleep is enabled.

•Disabled

•Enabled in S5 only

•Enabled in S4 and S5

Enabled in S4 and S5 is enabled by default.

Controls the speed of the system fan. This option is disabled by default. NOTE: When enabled, the fan runs at full speed.

This option allows you to enable USB devices to wake the computer from standby.

•Enable USB Wake Support - This option is enabled by default.

This option allows the computer to power up from the off state when triggered by a special LAN signal. Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. This feature only works when the computer is connected to AC power supply. The options differ based on the form factor.

•Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN.

•LAN Only - Allows the system to be powered on by special LAN signals.

•WLAN Only - Allows the system to be powered on by special WLAN signals. (For Ultra Small Form Factor only)

•LAN or WLAN - Allows the system to be powered on by special LAN or WLAN signals. (For Ultra Small Form Factor only)

•LAN with PXE Boot - Allows the system to be powered on by special LAN signals.

This option is Disabled by default.

This option lets you block entering to sleep (S3 state) in operating system environment.

•Block Sleep (S3 state) - This option is disabled by default.

Intel Smart Connect

This option is disabled by default. If this option is enabled, the feature will periodically

Technology

sense the nearby wireless connection while the system is asleep. The Smart Connect

 

will synchronize the email or social media applications that are open, when the

 

computer enters the sleep state.

Table 8. POST Behavior

 

 

 

Option

Description

 

 

Adapter Warnings

This option allows you to choose whether the system should display warning

 

messages when a certain power adapter is used. This option is enabled by default.

Numlock LED

Specifies if the NumLock function can be enabled when the system boots. This option

 

is enabled by default.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Regulatory Model W07B Regulatory Type W07B001 Dell Inc. All Rights Reserved Contents Troubleshooting Your Computer System SetupDiagnostics Technical Specifications Contacting DellWorking on Your Computer Before Working Inside Your ComputerTurning Off Your Computer Recommended ToolsClick Shut Down After Working Inside Your Computer Important InformationPage Removing and Installing Components System OverviewRemoving the Stand Cover Installing the Stand CoverRemoving the Vesa Stand Installing the Vesa Stand Removing the Back CoverRemove the back cover from the computer Installing the Back Cover Removing the Optical Disk DriveRemoving the Control Board Installing the Optical Disk DriveRemove Installing the Control Board Removing the Wireless Local Area Network Wlan CardInstalling the Wlan Card Removing the MemoryInstalling the Memory Removing the System Board CoverInstalling the System Board Cover Removing the Coin-Cell BatteryInstalling the Coin-Cell Battery Removing the Heat SinkInstalling the System Fan Installing the Heat SinkRemoving the System Fan Removing the Intrusion Switch Installing the ProcessorRemoving the Processor Installing the Intrusion Switch Removing the SpeakersInstalling the Speakers Removing the Power SwitchInstalling the Power Switch Removing the Hard DrivePage Installing the Hard Drive Removing the System BoardPage Page Page Serial port connector System Board ComponentsInstalling the System Board Removing the Display BracketPage Page Installing the Display Bracket Removing the Camera Installing the CameraVesa stand Stand cover Removing the Serial Port Installing the Serial Port Page Following table displays the system setup navigation keys System SetupBoot Sequence Navigation KeysSystem Setup Options Not selected. The other options are Advanced Boot OptionsExit Exits and starts the computer Date/TimeUSB Configuration Reporting Technology specificationEnable Smart Reporting This option is disabled by default Enable Audio option is selectedPrimary password With a system password and/or HDD passwordSystem Password Internal HDD-0 PasswordDisabled EnabledOption is enabled by default Keys will restore to default settingsAll Enabled by default Enabled by defaultOptionDescription Bluetooth Verbose Mode 255.255.255.255Re-start the computer Updating the BiosSystem and Setup Password ComputerPress Y to save the changes. The computer reboots Diagnostics Enhanced Pre-Boot System Assessment ePSA DiagnosticsPage Troubleshooting Your Computer Important Information Diagnostic Power LED CodesError Messages Beep CodesMessage Page Specification Technical SpecificationsFeature Feature SpecificationMini PCI Express One Control keysAdapter bracket Ports and Connectors Kg 8.63 kg 17.94 lb 19.02 lb Feature Specification Non-TouchTilt Degrees to 30 degrees Reading data from or writing data to the hard drivePower supply diagnostic light Back of the computer and the electrical outletPage Contacting Dell
Top Page Image Contents