Dell 7010 Signals. For Ultra Small Form Factor only, Numlock LED, Is enabled by default

Page 42

Option	Description

	• LAN or WLAN - Allows the system to be powered on by special LAN or WLAN
	signals. (For Ultra Small Form Factor only)
	This option is Disabled by default.
Block Sleep	This option lets you block entering to sleep (S3 state) in operating system
	environment.
	• Block Sleep (S3 state) - This option is disabled by default.
Table 8. POST Behavior

Option	Description

Numlock LED	Specifies if the NumLock function can be enabled when the system boots. This option
	is enabled by default.
Keyboard Errors	Specifies whether keyboard related errors are reported when it boots. This option is
	enabled by default.
POST Hotkeys	Specifies whether the sign-on screen displays a message, that displays the keystroke
	sequence required to enter the BIOS Boot Option Menu.
	• Enable F12 Boot Option menu - This option is enabled by default.
Table 9. Virtualization Support

Option	Description

Virtualization	This option specifies whether a Virtual Machine Monitor (VMM) can utilize the
	additional hardware capabilities provided by Intel Virtualization technology.
	• Enable Intel Virtualization Technology - This option is enabled by default.
VT for Direct I/O	Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional
	hardware capabilities provided by Intel® Virtualization technology for direct I/O.
	• Enable Intel Virtualization Technology for Direct I/O - This option is enabled
	by default.
Trusted Execution	This option specifies whether a Measured Virtual Machine Monitor (MVMM) can
	utilize the additional hardware capabilities provided by Intel Trusted Execution
	technology. The TPM virtualization technology, and Virtualization technology for
	direct I/O must be enabled to use this feature.
	• Trusted Execution - This option is disabled by default.
Table 10. Maintenance

Option	Description

Service Tag	Displays the Service Tag of your computer.
Asset Tag	Allows you to create a system asset tag if an asset tag is not already set. This option
	is not set by default.

42

Image 42

Contents Regulatory Model D03S Regulatory Type D03S002 Dell Inc Contents Troubleshooting Your Computer System SetupDiagnostics Specifications Contacting DellWorking on Your Computer Before Working Inside Your ComputerTurning Off Your Computer After Working Inside Your ComputerClick Shut Down Recommended Tools Removing and Installing ComponentsInstalling the Cover Removing the CoverInstalling the Front Bezel Removing the Front BezelRemoving The Wireless Local Area Network Wlan Card Installing The Wlan CardRemoving the Drive Cage Installing the Drive Cage Removing the Optical DrivePage Installing the Optical Drive Removing the Hard DrivePry the sides of the bracket to remove the optical drive Installing the Hard Drive Removing the Intrusion Switch Installing the Intrusion Switch Memory Module GuidelinesRemoving the Memory Installing the Memory Removing the Coin-Cell BatteryInstalling the Coin-Cell Battery Removing the System FanRemove Cover Front bezel Drive cage Page Installing the System Fan Removing the SpeakerInstalling the Speaker Removing the Power-Switch CableInstalling the Power-Switch Cable Removing the Input/Output I/O PanelInstalling the Input/Output I/O Panel Removing the Power SupplyRemove Cover Page Page Installing the Power Supply Lift the power supply out of the computerRemoving the Heat Sink Page Installing the Heat Sink Removing the ProcessorInstalling the Processor Removing the System BoardPage Power connector System Board ComponentsProcessor Installing the System Board Page Following table displays the system setup navigation keys System SetupBoot Sequence Navigation KeysSystem Setup Options Ahci Sata is configured for Ahci mode Disabled The Sata controllers are hiddenATA Sata is configured for ATA mode RAID on Sata is configured to support RAID modeOptionDescription Permitted when an administrator password is set They are set. This option is disabled by defaultPassword Change Is enabled and visible to the operating systemAll Enabled by default Reset All Keys- Resets to default settingKeys will restore to default settings Option is enabled by defaultPower loss. You can set the AC Recovery to Disabled by defaultAC Recovery Power Off defaultKeyboard Errors Signals. For Ultra Small Form Factor onlyIs enabled by default Sequence required to enter the Bios Boot Option MenuSerr Messages Software communicates. The default IP address isCommunicate. The default IP port is ImageServer IPSystem and Setup Password Updating the BiosJumper Settings Click Drivers & DownloadsAssigning a System Password and Setup Password ComputerDisabling a System Password Diagnostics Enhanced Pre-Boot System Assessment ePSA DiagnosticsPage Amber LED State White LED State Description Troubleshooting Your ComputerPower LED Diagnostics Possible system board resource and/or hardware failureError Messages Beep CodeProblem Error Message DescriptionFailure Configuration Information-please Run Setup program Invalid MemorySystem installed on it. Insert a bootable floppy disk Disk errorNot a boot diskette Value Memory sizeWrite fault Write fault onSelected drive Page Specification SpecificationsFeature Feature SpecificationExpress Chipset CPU-GPU Combo Discrete PCI Express x16 graphics adapterIntegrated Two Channel High Definition Audio Audio Front Panel Back PanelMini-Tower and Desktop One 36-pin connector Form factorPCI Express x1 data width maximum one PCI Express lane Connector Front of the computer Power button lightWhite light indicates sleep state of the computer Power Wattage Maximum Heat Dissipation Voltage Physical Height Width Depth WeightPhysical Height Width Depth Weight Ultra Small Form Factor 24.00 cm 30 kg 7.28 lb InchesPage Contacting Dell

Related manuals

Manual 47 pages 49.28 Kb