Dell 7010 Hyper-Thread Control, Disabled by default, AC Recovery, Power Off default, Power On

Page 41

Option	Description

Hyper-Thread Control	Allows you to enable or disable the Hyper-Threading technology. This option is
	disabled by default.
Table 7. Power Management

Option	Description

AC Recovery	Specifies how the computer will respond when AC power is applied after an AC
	power loss. You can set the AC Recovery to:
	•	Power Off (default)
	•	Power On
	•	Last Power State

Auto On Time

Deep Sleep Control

Fan Control Override

USB Wake Support

Wake on LAN

This option sets the time of the day when you would like the system to turn on automatically. Time is kept in standard 12-hour format (hour:minutes:seconds). The startup time can be changed by typing the values in the time and A.M./P.M. fields.

•Disabled - The system will not automatically power up.

•Every Day - The system will power up every day at the time you specified above .

•Weekdays - The system will power up Monday through Friday at the time you specified above.

•Select Days - The system will power up on days selected above at the time you specified above.

NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled.

Allows you to define the controls when Deep Sleep is enabled.

•Disabled

•Enabled in S5 only

•Enabled in S4 and S5

This option is disabled by default.

Controls the speed of the system fan. This option is disabled by default. NOTE: When enabled, the fan runs at full speed.

This option allows you to enable USB devices to wake the computer from standby.

•Enable USB Wake Support - This option is disabled by default.

This option allows the computer to power up from the off state when triggered by a special LAN signal. Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. This feature only works when the computer is connected to AC power supply. The options differ based on the form factor.

•Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN.

•LAN Only - Allows the system to be powered on by special LAN signals.

•WLAN Only - Allows the system to be powered on by special WLAN signals. (For Ultra Small Form Factor only)

41

Image 41

Contents Regulatory Model D03S Regulatory Type D03S002 Dell Inc Contents Diagnostics System SetupTroubleshooting Your Computer Specifications Contacting DellBefore Working Inside Your Computer Working on Your ComputerClick Shut Down Turning Off Your ComputerAfter Working Inside Your Computer Installing the Cover Removing and Installing ComponentsRecommended Tools Removing the CoverRemoving the Front Bezel Installing the Front BezelInstalling The Wlan Card Removing The Wireless Local Area Network Wlan CardRemoving the Drive Cage Removing the Optical Drive Installing the Drive CagePage Pry the sides of the bracket to remove the optical drive Installing the Optical DriveRemoving the Hard Drive Installing the Hard Drive Removing the Intrusion Switch Removing the Memory Installing the Intrusion SwitchMemory Module Guidelines Removing the Coin-Cell Battery Installing the MemoryRemove Cover Front bezel Drive cage Installing the Coin-Cell BatteryRemoving the System Fan Page Removing the Speaker Installing the System FanRemoving the Power-Switch Cable Installing the SpeakerRemoving the Input/Output I/O Panel Installing the Power-Switch CableRemove Cover Installing the Input/Output I/O PanelRemoving the Power Supply Page Page Lift the power supply out of the computer Installing the Power SupplyRemoving the Heat Sink Page Removing the Processor Installing the Heat SinkRemoving the System Board Installing the ProcessorPage Processor Power connectorSystem Board Components Installing the System Board Page Boot Sequence System SetupFollowing table displays the system setup navigation keys Navigation KeysSystem Setup Options ATA Sata is configured for ATA mode Disabled The Sata controllers are hiddenAhci Sata is configured for Ahci mode RAID on Sata is configured to support RAID modeOptionDescription Password Change They are set. This option is disabled by defaultPermitted when an administrator password is set Is enabled and visible to the operating systemKeys will restore to default settings Reset All Keys- Resets to default settingAll Enabled by default Option is enabled by defaultAC Recovery Disabled by defaultPower loss. You can set the AC Recovery to Power Off defaultIs enabled by default Signals. For Ultra Small Form Factor onlyKeyboard Errors Sequence required to enter the Bios Boot Option MenuCommunicate. The default IP port is Software communicates. The default IP address isSerr Messages ImageServer IPJumper Settings Updating the BiosSystem and Setup Password Click Drivers & DownloadsComputer Assigning a System Password and Setup PasswordDisabling a System Password Enhanced Pre-Boot System Assessment ePSA Diagnostics DiagnosticsPage Power LED Diagnostics Troubleshooting Your ComputerAmber LED State White LED State Description Possible system board resource and/or hardware failureBeep Code Error MessagesFailure Configuration Error Message DescriptionProblem Information-please Run Setup program Invalid MemoryNot a boot diskette Disk errorSystem installed on it. Insert a bootable floppy disk Value Memory sizeSelected drive Write faultWrite fault on Page Feature SpecificationsSpecification Feature SpecificationIntegrated Two Channel High Definition Audio Express Chipset CPU-GPU ComboDiscrete PCI Express x16 graphics adapter Back Panel Audio Front PanelPCI Express x1 data width maximum one PCI Express lane Mini-Tower and Desktop One 36-pin connectorForm factor White light indicates sleep state of the computer ConnectorFront of the computer Power button light Physical Height Width Depth Weight Power Wattage Maximum Heat Dissipation Voltage24.00 cm 30 kg 7.28 lb Inches Physical Height Width Depth Weight Ultra Small Form FactorPage Contacting Dell

Related manuals

Manual 47 pages 49.28 Kb