Dell 7010 Serr Messages, ImageServer IP, Software communicates. The default IP address is

Page 43

Option	Description

SERR Messages	Controls the SERR message mechanism. This option is not set by default. Some
	graphics cards require that the SERR message mechanism be disabled.
Table 11. Image Server

Option	Description

Lookup Method	Specifies how the ImageServer looks up the server address.
	•	Static IP
	• DNS (enabled by default)
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer.
ImageServer IP	Specifies the primary static IP address of the ImageServer with which the client
	software communicates. The default IP address is 255.255.255.255.
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer and when Lookup
		Method is set to Static IP.
ImageServer Port	Specifies the primary IP port of the ImageServer, which can be used by the client to
	communicate. The default IP port is 06910.
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer.
Client DHCP	Specifies how the client obtains the IP address.
	•	Static IP
	• DHCP (enabled by default)
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer.
Client IP	Specifies the static IP address of the client. The default IP address is 255.255.255.255.
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer and when Client DHCP is
		set to Static IP.
Client SubnetMask	Specifies the subnet mask of the client. The default setting is 255.255.255.255.
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer and when Client DHCP is
		set to Static IP.
Client Gateway	Specifies the gateway IP address for the client. The default setting is 255.255.255.255.
		NOTE: This field is only relevant when the Integrated NIC control in the System
		Configuration group is set to Enabled with ImageServer and when Client DHCP is
		set to Static IP.
License Status	Displays the current license status.

43

Image 43

Contents Regulatory Model D03S Regulatory Type D03S002 Dell Inc Contents Specifications Contacting Dell System SetupDiagnostics Troubleshooting Your ComputerBefore Working Inside Your Computer Working on Your ComputerAfter Working Inside Your Computer Turning Off Your ComputerClick Shut Down Removing the Cover Removing and Installing ComponentsInstalling the Cover Recommended ToolsRemoving the Front Bezel Installing the Front BezelInstalling The Wlan Card Removing The Wireless Local Area Network Wlan CardRemoving the Drive Cage Removing the Optical Drive Installing the Drive CagePage Removing the Hard Drive Installing the Optical DrivePry the sides of the bracket to remove the optical drive Installing the Hard Drive Removing the Intrusion Switch Memory Module Guidelines Installing the Intrusion SwitchRemoving the Memory Removing the Coin-Cell Battery Installing the MemoryRemoving the System Fan Installing the Coin-Cell BatteryRemove Cover Front bezel Drive cage Page Removing the Speaker Installing the System FanRemoving the Power-Switch Cable Installing the SpeakerRemoving the Input/Output I/O Panel Installing the Power-Switch CableRemoving the Power Supply Installing the Input/Output I/O PanelRemove Cover Page Page Lift the power supply out of the computer Installing the Power SupplyRemoving the Heat Sink Page Removing the Processor Installing the Heat SinkRemoving the System Board Installing the ProcessorPage System Board Components Power connectorProcessor Installing the System Board Page Navigation Keys System SetupBoot Sequence Following table displays the system setup navigation keysSystem Setup Options RAID on Sata is configured to support RAID mode Disabled The Sata controllers are hiddenATA Sata is configured for ATA mode Ahci Sata is configured for Ahci modeOptionDescription Is enabled and visible to the operating system They are set. This option is disabled by defaultPassword Change Permitted when an administrator password is setOption is enabled by default Reset All Keys- Resets to default settingKeys will restore to default settings All Enabled by defaultPower Off default Disabled by defaultAC Recovery Power loss. You can set the AC Recovery toSequence required to enter the Bios Boot Option Menu Signals. For Ultra Small Form Factor onlyIs enabled by default Keyboard ErrorsImageServer IP Software communicates. The default IP address isCommunicate. The default IP port is Serr MessagesClick Drivers & Downloads Updating the BiosJumper Settings System and Setup PasswordComputer Assigning a System Password and Setup PasswordDisabling a System Password Enhanced Pre-Boot System Assessment ePSA Diagnostics DiagnosticsPage Possible system board resource and/or hardware failure Troubleshooting Your ComputerPower LED Diagnostics Amber LED State White LED State DescriptionBeep Code Error MessagesInformation-please Run Setup program Invalid Memory Error Message DescriptionFailure Configuration ProblemValue Memory size Disk errorNot a boot diskette System installed on it. Insert a bootable floppy diskWrite fault on Write faultSelected drive Page Feature Specification SpecificationsFeature SpecificationDiscrete PCI Express x16 graphics adapter Express Chipset CPU-GPU ComboIntegrated Two Channel High Definition Audio Back Panel Audio Front PanelForm factor Mini-Tower and Desktop One 36-pin connectorPCI Express x1 data width maximum one PCI Express lane Front of the computer Power button light ConnectorWhite light indicates sleep state of the computer Physical Height Width Depth Weight Power Wattage Maximum Heat Dissipation Voltage24.00 cm 30 kg 7.28 lb Inches Physical Height Width Depth Weight Ultra Small Form FactorPage Contacting Dell

Related manuals

Manual 47 pages 49.28 Kb