Dell 7010 Turning Off Your Computer, After Working Inside Your Computer, Click Shut Down

Page 6

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

1.Shut down the operating system:

In Windows 8:

*Using a touch-enabled device:

a.Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

b.Select the and then select Shut down

*Using a mouse:

a.Point to upper-right corner of the screen and click Settings.

b.Click the and select Shut down.

In Windows 7:

1.Click Start.

2.Click Shut Down.

or

1.Click Start.

2.Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down..

2.Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 6 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.

1.Replace the cover.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.

2.Connect any telephone or network cables to your computer.

3.Connect your computer and all attached devices to their electrical outlets.

4.Turn on your computer.

5.If required, verify that the computer works correctly by running the Dell Diagnostics.

6

Image 6
Contents Regulatory Model D03S Regulatory Type D03S002 Dell Inc Contents Troubleshooting Your Computer System SetupDiagnostics Specifications Contacting DellWorking on Your Computer Before Working Inside Your ComputerTurning Off Your Computer After Working Inside Your ComputerClick Shut Down Recommended Tools Removing and Installing ComponentsInstalling the Cover Removing the CoverInstalling the Front Bezel Removing the Front BezelRemoving The Wireless Local Area Network Wlan Card Installing The Wlan CardRemoving the Drive Cage Installing the Drive Cage Removing the Optical DrivePage Installing the Optical Drive Removing the Hard DrivePry the sides of the bracket to remove the optical drive Installing the Hard Drive Removing the Intrusion Switch Installing the Intrusion Switch Memory Module GuidelinesRemoving the Memory Installing the Memory Removing the Coin-Cell BatteryInstalling the Coin-Cell Battery Removing the System FanRemove Cover Front bezel Drive cage Page Installing the System Fan Removing the SpeakerInstalling the Speaker Removing the Power-Switch CableInstalling the Power-Switch Cable Removing the Input/Output I/O PanelInstalling the Input/Output I/O Panel Removing the Power SupplyRemove Cover Page Page Installing the Power Supply Lift the power supply out of the computerRemoving the Heat Sink Page Installing the Heat Sink Removing the ProcessorInstalling the Processor Removing the System BoardPage Power connector System Board ComponentsProcessor Installing the System Board Page Following table displays the system setup navigation keys System SetupBoot Sequence Navigation KeysSystem Setup Options Ahci Sata is configured for Ahci mode Disabled The Sata controllers are hiddenATA Sata is configured for ATA mode RAID on Sata is configured to support RAID modeOptionDescription Permitted when an administrator password is set They are set. This option is disabled by defaultPassword Change Is enabled and visible to the operating systemAll Enabled by default Reset All Keys- Resets to default settingKeys will restore to default settings Option is enabled by defaultPower loss. You can set the AC Recovery to Disabled by defaultAC Recovery Power Off defaultKeyboard Errors Signals. For Ultra Small Form Factor onlyIs enabled by default Sequence required to enter the Bios Boot Option MenuSerr Messages Software communicates. The default IP address isCommunicate. The default IP port is ImageServer IPSystem and Setup Password Updating the BiosJumper Settings Click Drivers & DownloadsAssigning a System Password and Setup Password ComputerDisabling a System Password Diagnostics Enhanced Pre-Boot System Assessment ePSA DiagnosticsPage Amber LED State White LED State Description Troubleshooting Your ComputerPower LED Diagnostics Possible system board resource and/or hardware failureError Messages Beep CodeProblem Error Message DescriptionFailure Configuration Information-please Run Setup program Invalid MemorySystem installed on it. Insert a bootable floppy disk Disk errorNot a boot diskette Value Memory sizeWrite fault Write fault onSelected drive Page Specification SpecificationsFeature Feature SpecificationExpress Chipset CPU-GPU Combo Discrete PCI Express x16 graphics adapterIntegrated Two Channel High Definition Audio Audio Front Panel Back PanelMini-Tower and Desktop One 36-pin connector Form factorPCI Express x1 data width maximum one PCI Express lane Connector Front of the computer Power button lightWhite light indicates sleep state of the computer Power Wattage Maximum Heat Dissipation Voltage Physical Height Width Depth WeightPhysical Height Width Depth Weight Ultra Small Form Factor 24.00 cm 30 kg 7.28 lb InchesPage Contacting Dell
Related manuals
Manual 47 pages 49.28 Kb