Dell 7010 owner manual Write fault on, Selected drive

Page 53

Error Message

Time-of-day not set- please run the System Setup program

Description

The time or date stored in System Setup does not match the computer clock.

Timer chip counter 2 A chip on the system board may be malfunctioning. failed

Unexpected interrupt The keyboard controller may be malfunctioning or a memory module may be loose. in protected mode

WARNING: Dell's During initial startup, the drive detected possible error conditions. When your computer

Disk Monitoring finishes booting, immediately back up your data and replace your hard drive (for installation System has detected procedures, see "Adding and Removing Parts" for your computer type). If no replacement drive that drive [0/1] on the is immediately available and the drive is not the only bootable drive, enter System Setup and [primary/secondary] change the appropriate drive setting to None. Then remove the drive from the computer.

EIDE controller is operating outside of normal specifications. It is advisable to immediately back up your data and replace your hard drive by calling your support desk or Dell.

Write fault

The operating system cannot write to the floppy or hard drive.

Write fault on

The operating system cannot write to the floppy or hard drive.

selected drive

 

53

Image 53
Contents Regulatory Model D03S Regulatory Type D03S002 Dell Inc Contents Diagnostics System SetupTroubleshooting Your Computer Specifications Contacting DellBefore Working Inside Your Computer Working on Your ComputerClick Shut Down Turning Off Your ComputerAfter Working Inside Your Computer Installing the Cover Removing and Installing ComponentsRecommended Tools Removing the CoverRemoving the Front Bezel Installing the Front BezelInstalling The Wlan Card Removing The Wireless Local Area Network Wlan CardRemoving the Drive Cage Removing the Optical Drive Installing the Drive CagePage Pry the sides of the bracket to remove the optical drive Installing the Optical DriveRemoving the Hard Drive Installing the Hard Drive Removing the Intrusion Switch Removing the Memory Installing the Intrusion SwitchMemory Module Guidelines Removing the Coin-Cell Battery Installing the MemoryRemove Cover Front bezel Drive cage Installing the Coin-Cell BatteryRemoving the System Fan Page Removing the Speaker Installing the System FanRemoving the Power-Switch Cable Installing the SpeakerRemoving the Input/Output I/O Panel Installing the Power-Switch CableRemove Cover Installing the Input/Output I/O PanelRemoving the Power Supply Page Page Lift the power supply out of the computer Installing the Power SupplyRemoving the Heat Sink Page Removing the Processor Installing the Heat SinkRemoving the System Board Installing the ProcessorPage Processor Power connectorSystem Board Components Installing the System Board Page Boot Sequence System SetupFollowing table displays the system setup navigation keys Navigation KeysSystem Setup Options ATA Sata is configured for ATA mode Disabled The Sata controllers are hiddenAhci Sata is configured for Ahci mode RAID on Sata is configured to support RAID modeOptionDescription Password Change They are set. This option is disabled by defaultPermitted when an administrator password is set Is enabled and visible to the operating systemKeys will restore to default settings Reset All Keys- Resets to default settingAll Enabled by default Option is enabled by defaultAC Recovery Disabled by defaultPower loss. You can set the AC Recovery to Power Off defaultIs enabled by default Signals. For Ultra Small Form Factor onlyKeyboard Errors Sequence required to enter the Bios Boot Option MenuCommunicate. The default IP port is Software communicates. The default IP address isSerr Messages ImageServer IPJumper Settings Updating the BiosSystem and Setup Password Click Drivers & DownloadsComputer Assigning a System Password and Setup PasswordDisabling a System Password Enhanced Pre-Boot System Assessment ePSA Diagnostics DiagnosticsPage Power LED Diagnostics Troubleshooting Your ComputerAmber LED State White LED State Description Possible system board resource and/or hardware failureBeep Code Error MessagesFailure Configuration Error Message DescriptionProblem Information-please Run Setup program Invalid MemoryNot a boot diskette Disk errorSystem installed on it. Insert a bootable floppy disk Value Memory sizeSelected drive Write faultWrite fault on Page Feature SpecificationsSpecification Feature SpecificationIntegrated Two Channel High Definition Audio Express Chipset CPU-GPU ComboDiscrete PCI Express x16 graphics adapter Back Panel Audio Front PanelPCI Express x1 data width maximum one PCI Express lane Mini-Tower and Desktop One 36-pin connectorForm factor White light indicates sleep state of the computer ConnectorFront of the computer Power button light Physical Height Width Depth Weight Power Wattage Maximum Heat Dissipation Voltage24.00 cm 30 kg 7.28 lb Inches Physical Height Width Depth Weight Ultra Small Form FactorPage Contacting Dell
Related manuals
Manual 47 pages 49.28 Kb