AMX Comprehensive Guide to Relay Control Solutions

Page 29

NXC-REL10 Relay Control Card

NXC-REL10 Relay Control Card

The NXC-REL10 Relay Control Card (FG2020) provides ten relays that support devices that employ simple momentary or latching contact-closure control, with LED feedback. FIG. 6 shows the REL-10 card:

NO and NC 3-pin jumpers J1 - J5

NO and NC 3-pin jumpers J6 - J10

FIG. 6 NXC-REL10 Relay 10 Control card

Specifications

NXC-REL10 Specifications

Power Requirements:	260 mA @ 12 VDC

Operation:	Relay 1-10: ten relays, 1A @ , 24 VAC / 28 VDC

LEDs:	Ten red LEDs light to show ON status activity for each relay

Wiring:	•	Two 10-pin 3.5 mm captive-screw terminals
	•	Commoning strip (metal)

Pinouts and Functions

NXC-REL10 Pinouts and Functions

Pin

1

2

3

4

5

6

7

8

9

10

Function	Pin	Function
Relay 1A	11	Relay 6A
Relay 1B	12	Relay 6B
Relay 2A	13	Relay 7A
Relay 2B	14	Relay 7B
Relay 3A	15	Relay 8A
Relay 3B	16	Relay 8B
Relay 4A	17	Relay 9A
Relay 4B	18	Relay 9B
Relay 5A	19	Relay 10A
Relay 5B	20	Relay 10B

NXC-REL10 Channel Assignments

Channels 1-10 represent relays 1-10.

NetLinx Cardframe, Control Cards, and NetModules - Operation Reference Guide	23

Image 29

Contents Operation/Reference Guide NetLinx Cardframe Control Cards NetModulesAMX Limited Warranty and Disclaimer Table of Contents NXC-I/O10 Input/Output Control Card NXC-VOL4 Volume Control Card Page NXF Cardframe Specifications NXF Cardframe SpecificationsNXF CardFrame and NetModules OverviewPosition Rear Panel Components+12 VDC PWR NXS-NMS NetModules NXS-NMS NetModules SpecificationsNumber PortMounting modules into an equipment rack NXC-COM2 Specifications SpecificationsNXC-COM2 Dual COM Port Control Card DeviceidNXC-COM2 Programming Information Pinouts and Wiring ConfigurationNXC-COM2 Channel Assignment Chardm ChardCtspsh GET BaudRxclr HsonRxoff RxonTxclr NXC-COM2 SendString Escape SequencesXoff XON27,18,1 Command Description 27,18,027,19,time 27,20,0NXC-I/O10 Input/Output Control Card NXC-I/O10 SpecificationsSetting the Switch/Voltage Mode Jumpers Pinouts, Signals, and I/O Mode FunctionsNXC-I/O10 Pinouts, Signals, and I/O Mode Functions NXC-I/O10 Channel AssignmentsOpen mode setting Setting the Voltage Clamp Jumper +12V or Open+12 V mode setting default Page NXC-IRS4 4-Port IR/S Control Card NXC-IRS4 SpecificationsProgramming Information Pinouts, Signals, and FunctionsNXC-IRS4 Channel Assignments Cton CtofIroff GET ModePOD POFPton PtofSET Input Link SET IO Link Mode 1 Example x x x enter SET Mode XCH XchmMode 3 Example 100100… x Command Description XchmPage NXC-REL10 Relay Control Card NXC-REL10 SpecificationsPinouts and Functions NXC-REL10 Channel AssignmentsNo Normally open NXC-REL10 Connections/WiringIref NXC-VAI4 SpecificationsNXC-VAI4 Analog Voltage Control Card Channel Assignments NXC-VAI4 Pinouts, Signals, and FunctionsNXC-VAI4 Channel Assignments Channel State FunctionStops voltage ramping on Output 4 at current value Level Description NXC-VAI4 Output Level AssignmentsNXC-VAI4 Output Level Assignments NXC-VAI4 Input Level Assignments NXC-VAI4 SendCommandsNXC-VAI4 Input Level Assignments Levon LevoffRate CurveLevel Value Functions. Negative voltages are not valid for Inputs Page NXC-VOL4 Specifications NXC-VOL4 Volume Control CardAudio Channel Gain Ratio Jumper Settings NXC-VOL4 Connections/WiringNXC-VOL4 Pinouts, Signals, and Functions NXC-VOL4 Levels NXC-VOL4 Channel AssignmentsNXC-VOL4 Channel Assignments per port NXC-VOL4 LevelsSendlevel NXC-VOL4 SendCommandsPage It’s Your World Take Control