AMX nxc manual NXC-COM2 Dual COM Port Control Card, NXC-COM2 Specifications, Deviceid

Page 11

NXC-COM2 Dual COM Port Control Card

NXC-COM2 Dual COM Port Control Card

The NXC-COM2 Dual COM Port Control Card (FG2022) provides two RS-232, RS-422, or RS-485 control ports and LED feedback for remote sources connected to the NetLinx CardFrame, NI-4000 or NetModule. FIG. 3 shows the COM2 card.

ICSNET Status LED

LED 1

LED 4

FIG. 3 NXC-COM2 Dual COM Port Control card

Specifications

NXC-COM2 Specifications

Power Requirements:	140 mA @ 12 VDC

Operation:	Data 1-2: Two RS-232/422/485 control ports, supports XON/XOFF, CTS/RTS,
	300-230,400 baud

Status LEDs (2 per channel):	• Red LED shows TX (transmit) data activity
	• Yellow LED shows RX (receive) data activity
	- LED 1: CH1 TX (red)
	- LED 2: CH1 RX (yellow)
	- LED 3: CH2 TX (red)
	- LED 4: CH2 RX (yellow)
	• Green ICSP status LED (located on the board):
	- On = card is not in communication with the Master.
	- Blinks (1-second intervals) during normal operation.

Connections/wiring:	Two 10-pin 3.5 mm captive-screw terminals

DEVICE_ID:	$0107

NetLinx Cardframe, Control Cards, and NetModules - Operation Reference Guide	5

Image 11

Contents Operation/Reference Guide NetLinx Cardframe Control Cards NetModulesAMX Limited Warranty and Disclaimer Table of Contents NXC-I/O10 Input/Output Control Card NXC-VOL4 Volume Control Card Page Overview NXF Cardframe SpecificationsNXF Cardframe Specifications NXF CardFrame and NetModules Position Rear Panel Components +12 VDC PWR Port NXS-NMS NetModules SpecificationsNXS-NMS NetModules NumberMounting modules into an equipment rack Deviceid SpecificationsNXC-COM2 Specifications NXC-COM2 Dual COM Port Control CardNXC-COM2 Programming Information Pinouts and Wiring ConfigurationNXC-COM2 Channel Assignment GET Baud ChardChardm CtspshRxon HsonRxclr RxoffXON NXC-COM2 SendString Escape SequencesTxclr Xoff27,20,0 Command Description 27,18,027,18,1 27,19,timeNXC-I/O10 Input/Output Control Card NXC-I/O10 SpecificationsNXC-I/O10 Channel Assignments Pinouts, Signals, and I/O Mode FunctionsSetting the Switch/Voltage Mode Jumpers NXC-I/O10 Pinouts, Signals, and I/O Mode FunctionsOpen mode setting Setting the Voltage Clamp Jumper +12V or Open+12 V mode setting default Page NXC-IRS4 4-Port IR/S Control Card NXC-IRS4 SpecificationsProgramming Information Pinouts, Signals, and FunctionsNXC-IRS4 Channel Assignments Cton CtofPOF GET ModeIroff PODSET IO Link PtofPton SET Input LinkXchm SET ModeMode 1 Example x x x enter XCHMode 3 Example 100100… x Command Description XchmPage NXC-REL10 Channel Assignments NXC-REL10 SpecificationsNXC-REL10 Relay Control Card Pinouts and FunctionsNo Normally open NXC-REL10 Connections/WiringIref NXC-VAI4 SpecificationsNXC-VAI4 Analog Voltage Control Card Channel State Function NXC-VAI4 Pinouts, Signals, and FunctionsChannel Assignments NXC-VAI4 Channel AssignmentsStops voltage ramping on Output 4 at current value Level Description NXC-VAI4 Output Level AssignmentsNXC-VAI4 Output Level Assignments NXC-VAI4 Input Level Assignments NXC-VAI4 SendCommandsNXC-VAI4 Input Level Assignments Levon LevoffRate CurveLevel Value Functions. Negative voltages are not valid for Inputs Page NXC-VOL4 Specifications NXC-VOL4 Volume Control CardAudio Channel Gain Ratio Jumper Settings NXC-VOL4 Connections/WiringNXC-VOL4 Pinouts, Signals, and Functions NXC-VOL4 Levels NXC-VOL4 Channel AssignmentsNXC-VOL4 Levels NXC-VOL4 Channel Assignments per portSendlevel NXC-VOL4 SendCommandsPage It’s Your World Take Control