ADTRAN 2 x E1 user manual Plan a Plan B

Page 29

61280004L2-1C

Section 2 Installation

9.Reattach the cable assemblies from the ports labelled “Tx” and “Rx” on the RFC and the ports labelled “J1” and “J2” on the diplexer. Cable connections should be aligned to each other as follows.

Plan A

Plan B

RF converter Tx connected to

RF converter Tx connected to

Diplexer Port J1

Diplexer Port J2

RF converter Rx connected to

RF converter Rx connected to

Diplexer Port J2

Diplexer Port J1

10. Replace and secure the RFC cover.

 

For mastmounted systems, do the following to reconfigure the RFC interconnect:

1.Remove the lid of the mast RFC.

2.Disconnect the three cables attached to the diplexer. The diplexer may be identified by following the antenna connector to the middle connector of the diplexer. Leave the cables in the same positions.

3.Remove the two screws securing the diplexer and rotate the diplexer to reveal the opposite frequency plan label.

4.Reinstall the two screws and reattach the cables in the same positions – Minimum bend radius on cables is 3/4 inches (2 cm). Exercise care in handling and forming bends in these cables.

5.Reinstall the lid of the mast RFC.

TRACER 2 x E1 User’s Manual

19

Image 29
Contents Tracer 2 x E1 User’s Manual 61280004L2-1C R N I N G Radio Frequency Interface StatementRadio Frequency Interference Statement Table of Contents Operation Troubleshooting Warranty, Ordering and Return Information SpecificationsGlossary Appendix aIllustrations Viii Introduction Tracer DescriptionApplications Spread SpectrumTracer Description Forward Error CorrectionChannel Selection Direct SequenceBaseband Processor or BBP Tracer System ConfigurationE1 Interfaces VT100 RS-232 Interface Block diagram of the BBP is shown in FigureIf Signal Alarm ContactsPower Controls and IndicatorsFreq Non-volatile Memory Name FunctionRadio Frequency Converter or RFC Built-In Tests10. Front and Rear of Rackmount RFC Housing Antenna 100 mW Antenna SelectionUNPACK, Inspect InstallationGrounding InstallationE1 Interfaces 15 Pin RJ-48P O R T a N T Link PlanningAntenna Gain Antenna Feedline LossPath Availability Path LossGHZ, 1 Watt Transmitter Option Setting the Transmitter Power4 GHz Diplexer Setting the RFC Frequency Plan on NON 1 Watt 2.4 GHZ ModelsPlan a Plan B 8 GHz Diplexer Setting the RFC Frequency Plan on 5.8 GHZ ModelsApplying Power Connecting the BBP and the RFCAutomatic BBP Frequency Plan Spreading CodeRF LOW CO-LOCATING Multiple SystemsAntenna Alignment Remote Bert Alarm ContactsInstallation Operation PasswordVT100 User Interface RS-232 InterfaceSystem Status Screen OperationMain Menu Selections Tracer Main Menu Main Menu ScreenE1A Status Screen E1 Status / Configuration / LoopbackLink Performance History Screen Link Performance HistoryE1B Statistics E1A StatisticsProblem Descriptions and Recommended Actions SectionTROUBLESHOOTING4 TroubleshootingTroubleshooting Using the Front Panel Indicators GeneralRecommended Actions TroubleshootingCV/CRC Light on E1A or E1B is Lit when CRC is enabled LOS/OOF Light on E1A or E1B LBK-A or LBK-B is LitALM is Lit No Power LightTST Light is Lit After Pressing Remote Test Button Test Light is Lit or BlinkingRF Low Light is On Fail Light is Lit After Pressing Remote Test ButtonCV Alarm Troubleshooting Using the VT100 User InterfaceLOS Alarm RMT Alarm OOF AlarmCRC Alarm UA1 Alarm Code Sync Status Carrier Sync Status or E1 Mux Sync Status ES Values in E1A or E1B Performance History Menu Possible CauseRFC Link Up Status SES Values in E1A or E1B Performance History Menu Troubleshooting Specifications Power SpecificationsVT100 Terminal Interface Mechanical & EnvironmentalWarranty WARRANTY, Ordering and ReturnSales Repairs and ReturnsWarranty, Ordering and Return Information Acronyms Used in this Manual GlossaryGlossary Terminal Connection DB-25 Appendix a Cable ConnectionsPersonal Computer Connection DB-9 Modem Connection DB-25Appendix a Cable Connections