ADTRAN 2 x E1 user manual Illustrations

Page 9

61280004L2-1C

Table of Contents

Illustrations

 

 

Figure 1-1.

Typical Application

1

Figure 1-2.

Bandwidth Division

2

Figure 1-3.

BBP

3

Figure 1-4.

BBP Rear Panel

3

Figure 1-5.

BBP Block Diagram

4

Figure 1-6.

BBP Front Panel (with door closed)

6

Figure 1-7.

BBP Front Panel (with door open)

6

Figure 1-8.

RFC Function Block Diagram

8

Figure 1-9.

RFC Module

8

Figure 1-10.

Front and Rear of Rackmount RFC Housing

9

Figure 1-11.

Mastmount RFC Housing

10

Figure 2-1.

E1 Loopback Locations

14

Figure 2-2.

2.4 GHz Diplexer

18

Figure 2-3.

5.8 GHz Diplexer

20

Figure 3-1.

System Status Screen

26

Figure 3-2.

Main Menu Screen

27

Figure 3-3.

System Configuration Menu Screen

27

Figure 3-4.

E1A Status Screen

28

Figure 3-5.

E1B Status Screen

28

Figure 3-6.

Link Performance History Screen

29

Figure 3-7.

E1A Statistics Screen

30

Figure 3-8.

E1B Statistics Screen

30

TRACER 2 x E1 User’s Manual

vii

Image 9
Contents Tracer 2 x E1 User’s Manual 61280004L2-1C R N I N G Radio Frequency Interface StatementRadio Frequency Interference Statement Table of Contents Operation Troubleshooting Warranty, Ordering and Return Information SpecificationsGlossary Appendix aIllustrations Viii Introduction Tracer DescriptionApplications Spread SpectrumTracer Description Forward Error CorrectionChannel Selection Direct SequenceTracer System Configuration E1 InterfacesBaseband Processor or BBP VT100 RS-232 Interface Block diagram of the BBP is shown in FigureIf Signal Alarm ContactsPower Controls and IndicatorsFreq Non-volatile Memory Name FunctionRadio Frequency Converter or RFC Built-In Tests10. Front and Rear of Rackmount RFC Housing Antenna 100 mW Antenna SelectionUNPACK, Inspect InstallationGrounding InstallationE1 Interfaces 15 Pin RJ-48P O R T a N T Link PlanningAntenna Gain Antenna Feedline LossPath Availability Path LossGHZ, 1 Watt Transmitter Option Setting the Transmitter Power4 GHz Diplexer Setting the RFC Frequency Plan on NON 1 Watt 2.4 GHZ ModelsPlan a Plan B 8 GHz Diplexer Setting the RFC Frequency Plan on 5.8 GHZ ModelsApplying Power Connecting the BBP and the RFCAutomatic BBP Frequency Plan Spreading CodeCO-LOCATING Multiple Systems Antenna AlignmentRF LOW Remote Bert Alarm ContactsInstallation Operation PasswordVT100 User Interface RS-232 InterfaceOperation Main Menu SelectionsSystem Status Screen Tracer Main Menu Main Menu ScreenE1A Status Screen E1 Status / Configuration / LoopbackLink Performance History Screen Link Performance HistoryE1B Statistics E1A StatisticsProblem Descriptions and Recommended Actions SectionTROUBLESHOOTING4 TroubleshootingTroubleshooting Using the Front Panel Indicators GeneralTroubleshooting CV/CRC Light on E1A or E1B is Lit when CRC is enabledRecommended Actions LOS/OOF Light on E1A or E1B LBK-A or LBK-B is LitALM is Lit No Power LightTST Light is Lit After Pressing Remote Test Button Test Light is Lit or BlinkingRF Low Light is On Fail Light is Lit After Pressing Remote Test ButtonTroubleshooting Using the VT100 User Interface LOS AlarmCV Alarm OOF Alarm CRC AlarmRMT Alarm UA1 Alarm Code Sync Status Carrier Sync Status or E1 Mux Sync Status Possible Cause RFC Link Up StatusES Values in E1A or E1B Performance History Menu SES Values in E1A or E1B Performance History Menu Troubleshooting Specifications Power SpecificationsVT100 Terminal Interface Mechanical & EnvironmentalWarranty WARRANTY, Ordering and ReturnSales Repairs and ReturnsWarranty, Ordering and Return Information Acronyms Used in this Manual GlossaryGlossary Terminal Connection DB-25 Appendix a Cable ConnectionsPersonal Computer Connection DB-9 Modem Connection DB-25Appendix a Cable Connections