ADTRAN 2 x E1 Specifications, Warranty, Ordering and Return Information, Glossary, Appendix a

Page 8

61280004L2-1C

Table of Contents

Carrier Sync Status or E1 Mux Sync Status	41
RFC Link Up Status	42
ES Values in E1A or E1B Performance History Menu	42
SES Values in E1A or E1B Performance History Menu	43
Section 5. Specifications
Transmitter	45
Receiver	45
Frequency Plans	45
Spread Spectrum Data Pump	45
Interface Specifications	45
User Interface	45
VT100 Terminal Interface	46
Mechanical & Environmental	46
Power	46
Section 6. Warranty, Ordering and Return Information
Warranty	47
Sales	47
Repairs and Returns	47
Technical Support	47
Glossary
Acronyms Used in This Manual	49
Appendix A.
Cable Connections	A-1
Terminal Connection (DB-25)	A-1
Personal Computer Connection (DB-9)	A-1
Modem Connection (DB-25)	A-1

vi	TRACER 2 x E1 User’s Manual

Image 8

Contents Tracer 2 x E1 User’s Manual 61280004L2-1C Radio Frequency Interface Statement R N I N GRadio Frequency Interference Statement Table of Contents Operation Troubleshooting Specifications Warranty, Ordering and Return InformationGlossary Appendix aIllustrations Viii Tracer Description IntroductionApplications Spread SpectrumForward Error Correction Tracer DescriptionChannel Selection Direct SequenceBaseband Processor or BBP Tracer System ConfigurationE1 Interfaces Block diagram of the BBP is shown in Figure VT100 RS-232 InterfaceAlarm Contacts If SignalPower Controls and IndicatorsFreq Name Function Non-volatile MemoryBuilt-In Tests Radio Frequency Converter or RFC10. Front and Rear of Rackmount RFC Housing Antenna Selection Antenna 100 mWInstallation UNPACK, InspectInstallation Grounding15 Pin RJ-48 E1 InterfacesLink Planning P O R T a N TAntenna Feedline Loss Antenna GainPath Loss Path AvailabilitySetting the Transmitter Power GHZ, 1 Watt Transmitter OptionSetting the RFC Frequency Plan on NON 1 Watt 2.4 GHZ Models 4 GHz DiplexerPlan a Plan B Setting the RFC Frequency Plan on 5.8 GHZ Models 8 GHz DiplexerConnecting the BBP and the RFC Applying PowerAutomatic BBP Frequency Plan Spreading CodeRF LOW CO-LOCATING Multiple SystemsAntenna Alignment Alarm Contacts Remote BertInstallation Password OperationVT100 User Interface RS-232 InterfaceSystem Status Screen OperationMain Menu Selections Main Menu Screen Tracer Main MenuE1 Status / Configuration / Loopback E1A Status ScreenLink Performance History Link Performance History ScreenE1A Statistics E1B StatisticsSectionTROUBLESHOOTING4 Troubleshooting Problem Descriptions and Recommended ActionsTroubleshooting Using the Front Panel Indicators GeneralRecommended Actions TroubleshootingCV/CRC Light on E1A or E1B is Lit when CRC is enabled LBK-A or LBK-B is Lit LOS/OOF Light on E1A or E1BNo Power Light ALM is LitTest Light is Lit or Blinking TST Light is Lit After Pressing Remote Test ButtonFail Light is Lit After Pressing Remote Test Button RF Low Light is OnCV Alarm Troubleshooting Using the VT100 User InterfaceLOS Alarm RMT Alarm OOF AlarmCRC Alarm UA1 Alarm Code Sync Status Carrier Sync Status or E1 Mux Sync Status ES Values in E1A or E1B Performance History Menu Possible CauseRFC Link Up Status SES Values in E1A or E1B Performance History Menu Troubleshooting Specifications Specifications PowerVT100 Terminal Interface Mechanical & EnvironmentalWARRANTY, Ordering and Return WarrantySales Repairs and ReturnsWarranty, Ordering and Return Information Glossary Acronyms Used in this ManualGlossary Appendix a Cable Connections Terminal Connection DB-25Personal Computer Connection DB-9 Modem Connection DB-25Appendix a Cable Connections