3Com WL-560 manual Using the Configuration Management System

Page 45

Using the Configuration Management System 39

Using the Access You can use the Access Control List to allow or prohibit access to the Control List wireless network from Ethernet clients.

Follow these steps to build the Access Control List:

1Under System Configuration, click Access Control List.

2On the Access Control List page, click Add. The Access Control List New ACL page appears.

3On the New ACL page, enter the MAC address of the client you want to add to the Access Control List, select the permission type, and click the Add button to substantially add it.

4Repeat steps 2 and 3 for each client.

5Select the System Default Mode:

■Allow—allows the client to access the Bridge.

■Deny—prohibits the client from accessing the Bridge.

CAUTION: With the Allow option of the System Default Mode selected, the Bridge allows all Ethernet frames except those carrying the

MAC addresses that are specified in the Access Control List and have the permission type Deny. Similarly, with the Deny option of the System Default Mode selected, the Bridge denies all Ethernet frames except those carrying the MAC addresses that are specified in the Access Control List and have the permission type Allow.

Make sure that the MAC address of the computer through which you are configuring the Bridge is not specified in the Access Control List with the permission type Deny if you want to set the access control type to Allow. If you want to set the Access Control Type to Deny, make sure that the MAC address of the computer is included in the Access Control List with the permission type Allow. Failure to do so results in access to the Bridge being blocked; the Bridge will no longer be configurable through the computer.

6Click Apply.

To delete one or more than one client(s) from the Access Control List, select the client(s) and then click Delete.

Image 45

Contents 3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Related ConventionsDocumentation FollowingDocumentation documentation Product Registration Support Introduction 802.11g 802.11aNetwork Configuration and Planning ConfigurationNetwork PlanningWireless Infrastructure Network ConfigurationsExample Workgroup Ad-Hoc NetworkBridge UnpackingBridge Wall-Mounting the Bridge Deciding Where to Place the BridgeRouting Cable Under the Cradle Securing the Locking Bar Connecting the Power ConnectingConnecting the Bridge About the Client List Connecting to a HubNetwork printers in areas that are not wired for Ethernet LED IndicatorsAttaching An Need to ConfigureExternal Antenna Determining if youNetworks without a Dhcp Server Determining if you Need to Configure the BridgeTo Wireless Client Infrastructure Bridge Default SettingsUsing the 3Com Installation CD Using the 3Com Installation CDInstalling the Bridge Configuring the Bridge Wireless Using the 3ComInfrastructure Device ManagerUsing the 3Com Wireless Infrastructure Device Manager Click ConfigureButton Description Using ManagementSystem Moving to a new configuration Clearing Applying System Configuration SettingsSystem Properties Apply Server, select Obtain an IP address automatically and clickSelect 802.11a to set the Bridge to operate with either Select Wireless Client Infrastructure to associate with anSelect Specify the Wireless LAN Service Area to allow Service AreaBeing used, click Long Wi-Fi Interoperable External and one internal antenna this settingSet the Data Preamble 40/64-bit Shared Key WEP No Security Open System128/152-bit Shared Key 104/128-bit Shared KeyAES Or DisableSecondary Radius Using the Configuration Management System About Uart Configuring Operation ModeConfiguring Network Serial Port Settings Configuring Uart SettingsReset Applying SettingsOr with the Bridge out of the cradle Under Tools, click Restore Factory DefaultsUsing Tftp Using FTP defaultUnder Tools, click Backup Wireless Workgroup Bridge Using HttpUnder Tools, click Restore Wireless Workgroup Bridge Summary Page Diagnosing ProblemsTroubleshooting Uninstalling DisconnectingUninstall 3Com Wireless Infrastructure Device Manager Disconnecting the BridgeFirmware Upgrading BridgeSolve Problems Service BenefitsRegister Your Product to GainProfessional Services WarrantyAccess Software Purchase ExtendedContact Us Directory of 3Com resources by region atLatin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor